Reference guide · Machinist speeds, tap drills and shop geometry
Three-wire thread measurement: best wire size and measurement over wires
By the Mirage Interactive team · Last checked
The three-wire method is the shop way to check the pitch diameter of an external thread. Three hardened wires of one diameter sit in the grooves, two on one side and one on the other, and a micrometer reads across them. One formula turns that reading into the pitch diameter, or the other way round, a target pitch diameter into the reading to cut to.
This guide gives the best wire size for a 60 degree thread, the reading over the best wires for the common metric and UNC sizes, and the pitch diameter from a measured reading. The numbers are for a thread with the flanks at 60 degrees and ignore the lead angle.
The short answer
Best wire W = 0.57735 x P, where P is the pitch. Measurement over the wires M = E + 3 x W - 0.86603 x P, with E the pitch diameter. Solved for E: E = M - 3 x W + 0.86603 x P.
An M10 x 1.5 thread has a basic pitch diameter of 9.0257 mm. With the best wire of 0.8660 mm the reading over the wires is 10.3248 mm. For 1/4-20 UNC the figures are 0.2175 in, 0.02887 in and 0.2608 in.
Tables
The first table gives the best wire and the wire limits (0.56 x P to 0.9 x P, the range for a 60 degree thread) by pitch, in millimetres and in threads per inch. The second and third give the basic pitch diameter, the best wire and the measurement over the best wires for common metric and UNC threads. Use your browser's print command to print this page: the tables print without the navigation.
| Pitch | Best wire (0.57735 x P) | Smallest wire (0.56 x P) | Largest wire (0.9 x P) |
|---|---|---|---|
| 0.5 mm | 0.2887 | 0.280 | 0.450 |
| 0.75 mm | 0.4330 | 0.420 | 0.675 |
| 1 mm | 0.5774 | 0.560 | 0.900 |
| 1.25 mm | 0.7217 | 0.700 | 1.125 |
| 1.5 mm | 0.8660 | 0.840 | 1.350 |
| 2 mm | 1.1547 | 1.120 | 1.800 |
| 2.5 mm | 1.4434 | 1.400 | 2.250 |
| 3 mm | 1.7321 | 1.680 | 2.700 |
| 8 TPI | 0.07217 | 0.0700 | 0.1125 |
| 10 TPI | 0.05774 | 0.0560 | 0.0900 |
| 12 TPI | 0.04811 | 0.0467 | 0.0750 |
| 13 TPI | 0.04441 | 0.0431 | 0.0692 |
| 16 TPI | 0.03608 | 0.0350 | 0.0563 |
| 18 TPI | 0.03208 | 0.0311 | 0.0500 |
| 20 TPI | 0.02887 | 0.0280 | 0.0450 |
| 24 TPI | 0.02406 | 0.0233 | 0.0375 |
| 32 TPI | 0.01804 | 0.0175 | 0.0281 |
Source: computed by the site build from the formulas below.
| Thread | Basic pitch diameter E (mm) | Best wire (mm) | Over wires M (mm) |
|---|---|---|---|
| M3 x 0.5 | 2.6752 | 0.2887 | 3.1083 |
| M4 x 0.7 | 3.5453 | 0.4041 | 4.1516 |
| M5 x 0.8 | 4.4804 | 0.4619 | 5.1732 |
| M6 x 1 | 5.3505 | 0.5774 | 6.2165 |
| M8 x 1.25 | 7.1881 | 0.7217 | 8.2706 |
| M10 x 1.5 | 9.0257 | 0.8660 | 10.3248 |
| M12 x 1.75 | 10.8633 | 1.0104 | 12.3789 |
| M16 x 2 | 14.7010 | 1.1547 | 16.4330 |
| M20 x 2.5 | 18.3762 | 1.4434 | 20.5413 |
| M24 x 3 | 22.0514 | 1.7321 | 24.6495 |
Source: computed by the site build from the formulas below.
| Thread | Basic pitch diameter E (in) | Best wire (in) | Over wires M (in) |
|---|---|---|---|
| #10-24 UNC | 0.1629 | 0.02406 | 0.1990 |
| 1/4-20 UNC | 0.2175 | 0.02887 | 0.2608 |
| 5/16-18 UNC | 0.2764 | 0.03208 | 0.3245 |
| 3/8-16 UNC | 0.3344 | 0.03608 | 0.3885 |
| 1/2-13 UNC | 0.4500 | 0.04441 | 0.5167 |
| 5/8-11 UNC | 0.5660 | 0.05249 | 0.6447 |
| 3/4-10 UNC | 0.6850 | 0.05774 | 0.7717 |
| 1-8 UNC | 0.9188 | 0.07217 | 1.0271 |
Source: computed by the site build from the formulas below.
Formulas
- Best wire
- W = P / (2 x cos(half angle)) = 0.57735 x P for a 60 degree thread
- The best wire touches the flanks at the pitch line, so the reading depends on the pitch diameter and not on the flank angle error.
- Measurement over wires
- M = E + W x (1 + 1 / sin(half angle)) - (P / 2) / tan(half angle)
- For a 60 degree thread the half angle is 30 degrees, which gives M = E + 3 x W - 0.86603 x P.
- Pitch diameter from the reading
- E = M - 3 x W + 0.86603 x P
- The same formula solved for E. Use it to see where a measured thread sits against its pitch diameter limits.
- Basic pitch diameter
- E = major diameter - 0.649519 x P
- For a 60 degree ISO or UN thread, 0.649519 is 3/8 x the square root of 3. The tolerance class moves the actual limits below or above this basic figure: take those from the thread standard.
Worked example
M10 x 1.5 and 1/4-20, then a reading turned back into a pitch diameter
- M10 x 1.5: the basic pitch diameter is 10 - 0.649519 x 1.5 = 9.0257 mm. The best wire is 0.57735 x 1.5 = 0.8660 mm. M = 9.0257 + 3 x 0.8660 - 0.86603 x 1.5 = 10.3248 mm.
- 1/4-20 UNC: the pitch is 1/20 = 0.05 in. Basic pitch diameter = 0.25 - 0.649519 x 0.05 = 0.2175 in. Best wire = 0.02887 in. M = 0.2175 + 3 x 0.02887 - 0.86603 x 0.05 = 0.2608 in.
- A measured reading of 10.300 mm over 0.8660 mm wires on the M10 x 1.5 thread gives E = 10.300 - 3 x 0.8660 + 0.86603 x 1.5 = 9.0010 mm, which is 0.0248 mm under the basic figure. Compare that with the lower limit of your tolerance class.
- Wires that are not the best size work too if they are inside the limits. With M10 x 1.5 the limits are 0.840 to 1.350 mm. A 0.9 mm wire gives M = 9.0257 + 3 x 0.9 - 0.86603 x 1.5 = 10.4267 mm.
Things to watch
- The formula ignores the lead angle of the thread. On a coarse pitch or a multi-start thread the lead correction can matter; for an ordinary single-start thread of fine or normal pitch it is small, and the standards give the correction where it is needed.
- The formula assumes a 60 degree thread with a true flank angle. An unusual thread form or a worn thread gives a reading that no longer means the pitch diameter.
- Use the pitch diameter limits of the tolerance class from the thread standard. The basic pitch diameter on this page is the target, not a limit.
- The wires and the micrometer matter as much as the formula. Wires should be matched, clean and hardened, and the measuring force should be light and steady.
Related guide: Tap drill chart and cutting speed (RPM) formula
More from this family: Milling feed rate calculator: feed, chip load and spindle speed · Bolt circle calculator: hole coordinates and chord spacing · Cutting speed calculator: spindle RPM from SFM or m/min · Taper per foot calculator: taper, half angle and diameters · Sine bar calculator: gauge block stack height for an angle · Tap drill size for 50, 65 and 75 percent thread
Skip the arithmetic
Cutting Speed, Tap Drill, Sine
Cutting Speed, Tap Drill, Sine does the best wire, the measurement over wires and the pitch diameter from a reading, next to sine bar, taper, dovetail, chord and radius and triangles, and does spindle speed, feed and tap drills too. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
What is the best wire size for a 60 degree thread?
0.57735 times the pitch. For a 1.5 mm pitch that is 0.8660 mm, and for 20 threads per inch it is 0.02887 in.
How do you calculate measurement over wires?
Add three wire diameters to the pitch diameter and subtract 0.86603 times the pitch. For M10 x 1.5 with the best wire that is 10.3248 mm.
Does the three-wire method work for any thread angle?
The method does, but the formula changes with the half angle. This page covers the 60 degree thread of ISO metric and UN threads.
