Reference guide · Machinist speeds, tap drills and shop geometry
Sine bar calculator: gauge block stack height for an angle
By the Mirage Interactive team · Last checked
A sine bar is a hardened bar with a roller at each end, a known distance apart. Rest one roller on the surface plate, lift the other on a stack of gauge blocks, and the bar tilts to an angle that follows from the stack height alone.
This guide gives the stack height for any angle on the usual bar lengths and the angle for any stack, and shows how much a small error in the stack costs in angle.
The short answer
Stack height h = bar length L x sin(angle). The bar length is the distance between the roller centres, not the length of the steel. For a known stack the angle is arcsin(h / L).
A 10 inch bar set to 20 degrees needs a stack of 3.4202 inches. A 5 inch bar with a 1.2500 inch stack stands at 14.4775 degrees.
Tables
The first table gives the stack height for common angles on four bar lengths: 5 and 10 inch bars in inches, 100 and 200 mm bars in millimetres. The second gives the angle that a given stack height makes on a 5 inch and a 10 inch bar. Use your browser's print command to print this page: the tables print without the navigation.
| Angle (deg) | 5 in bar (in) | 10 in bar (in) | 100 mm bar (mm) | 200 mm bar (mm) |
|---|---|---|---|---|
| 1 | 0.0873 | 0.1745 | 1.745 | 3.490 |
| 2 | 0.1745 | 0.3490 | 3.490 | 6.980 |
| 3 | 0.2617 | 0.5234 | 5.234 | 10.467 |
| 5 | 0.4358 | 0.8716 | 8.716 | 17.431 |
| 7.5 | 0.6526 | 1.3053 | 13.053 | 26.105 |
| 10 | 0.8682 | 1.7365 | 17.365 | 34.730 |
| 12.5 | 1.0822 | 2.1644 | 21.644 | 43.288 |
| 15 | 1.2941 | 2.5882 | 25.882 | 51.764 |
| 20 | 1.7101 | 3.4202 | 34.202 | 68.404 |
| 25 | 2.1131 | 4.2262 | 42.262 | 84.524 |
| 30 | 2.5000 | 5.0000 | 50.000 | 100.000 |
| 35 | 2.8679 | 5.7358 | 57.358 | 114.715 |
| 40 | 3.2139 | 6.4279 | 64.279 | 128.558 |
| 45 | 3.5355 | 7.0711 | 70.711 | 141.421 |
Source: computed by the site build from the formulas below.
| Stack height (in) | Angle on 5 in bar (deg) | Angle on 10 in bar (deg) |
|---|---|---|
| 0.25 | 2.8660 | 1.4325 |
| 0.50 | 5.7392 | 2.8660 |
| 0.75 | 8.6269 | 4.3012 |
| 1.00 | 11.5370 | 5.7392 |
| 1.50 | 17.4576 | 8.6269 |
| 2.00 | 23.5782 | 11.5370 |
| 2.50 | 30.0000 | 14.4775 |
| 3.00 | 36.8699 | 17.4576 |
| 3.50 | 44.4270 | 20.4873 |
Source: computed by the site build from the formulas below.
Formulas
- Stack height for an angle
- h = L x sin(angle)
- L is the roller centre distance and h is the difference in height between the two roller centres, which equals the stack height when both rollers have the same diameter and rest on the same plate.
- Angle for a stack height
- angle = arcsin(h / L) = arctan(h / square root of (L^2 - h^2))
- The two forms are the same. The second never divides by a value near zero, so it stays accurate for small stacks.
- Horizontal distance between the roller centres
- run = L x cos(angle)
- This is the length the bar covers along the plate, useful when you check where the second roller falls.
- Angle error from a stack error
- error (radians) = stack error / (L x cos(angle))
- A stack that is off by a small amount moves the angle by that amount divided by the bar length times the cosine of the angle.
Worked example
A 10 inch bar at 20 degrees, then a check from the stack
- Stack height = 10 x sin 20 degrees = 10 x 0.342020 = 3.4202 inches. Build that with gauge blocks to the nearest 0.0001 inch.
- The roller centres are 9.3969 inches apart horizontally (10 x cos 20 degrees), so the bar covers about that much of the plate.
- Check the other way. For a 5 inch bar and a 1.2500 inch stack, the angle is arcsin(1.25 / 5) = 14.4775 degrees (14 degrees 28.7 minutes).
- How much does a stack error matter? On a 5 inch bar at 30 degrees, 0.0001 inch of stack error moves the angle by 0.0001 / (5 x cos 30 degrees) = 4.8 arc-seconds. Longer bars and smaller angles are less sensitive.
- In millimetres, a 127 mm bar (5 inch) at 0.5 degrees needs a stack of 1.1083 mm, which is 0.0436 inch.
Things to watch
- A sine bar is not advised above 45 degrees: the stack gets tall and a small error in height grows quickly in angle. Use a different setup for steep angles.
- The formula assumes the rollers have equal diameter and the bar length is the true centre distance. Check the figure on the bar, because some bars are marked in different units.
- Gauge blocks must be wrung together and the surface plate clean. The angle can be only as good as the stack and the plate.
Related guide: Tap drill chart and cutting speed (RPM) formula
More from this family: Milling feed rate calculator: feed, chip load and spindle speed · Bolt circle calculator: hole coordinates and chord spacing · Cutting speed calculator: spindle RPM from SFM or m/min · Three-wire thread measurement: best wire size and measurement over wires · Taper per foot calculator: taper, half angle and diameters · Tap drill size for 50, 65 and 75 percent thread
Skip the arithmetic
Cutting Speed, Tap Drill, Sine
Cutting Speed, Tap Drill, Sine includes a sine bar tool among its shop geometry, next to taper, thread wires, dovetail, chord and radius and triangles, and does spindle speed, feed and tap drills too. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do you calculate sine bar height?
Multiply the bar length, between the roller centres, by the sine of the angle. A 5 inch bar at 30 degrees needs 2.5000 inches.
How do you find the angle from a gauge block stack?
Divide the stack height by the bar length and take the arcsine. A 1.25 inch stack on a 5 inch bar gives 14.48 degrees.
What is the largest angle for a sine bar?
Practice is to stay at or below 45 degrees, because the angle gets more sensitive to stack error as it steepens.
