Reference guide · Machinist speeds, tap drills and shop geometry
Tap drill chart and cutting speed (RPM) formula
By the Mirage Interactive team · Last checked
A tap drill chart tells you which drill to use before you tap a thread. The drill is a little bigger than the thread's minor diameter, so the tap cuts about 75 percent of a full thread: strong enough for most work and much easier on the tap than a full 100 percent thread.
This guide also gives the cutting speed formula, with an RPM table so you can set a spindle speed without a calculator.
Printable tables
Tap drills for common inch and metric coarse threads, and spindle RPM by surface speed and diameter. Use your browser's print command to print this page: the tables print without the navigation.
| Thread | Pitch (mm) | Formula drill (mm) | Chart drill | Drill diameter (mm) | Thread (%) |
|---|---|---|---|---|---|
| #6-32 UNC | 0.794 | 2.711 | #36 | 2.705 | 78 |
| #8-32 UNC | 0.794 | 3.372 | #29 | 3.454 | 69 |
| #10-24 UNC | 1.058 | 3.768 | #25 | 3.797 | 75 |
| #10-32 UNF | 0.794 | 4.032 | #21 | 4.039 | 76 |
| 1/4-20 UNC | 1.27 | 5.08 | #7 | 5.105 | 75 |
| 1/4-28 UNF | 0.907 | 5.443 | #3 | 5.41 | 80 |
| 5/16-18 UNC | 1.411 | 6.526 | F | 6.528 | 77 |
| 3/8-16 UNC | 1.587 | 7.938 | 5/16 | 7.938 | 77 |
| 1/2-13 UNC | 1.954 | 10.746 | 27/64 | 10.716 | 78 |
| 5/8-11 UNC | 2.309 | 13.566 | 17/32 | 13.494 | 79 |
| 3/4-10 UNC | 2.54 | 16.51 | 21/32 | 16.669 | 72 |
Source: The Cutting Speed app's engine test cases for tap drill sizes.
| Thread | Pitch (mm) | Formula drill (mm) | Chart drill | Drill diameter (mm) | Thread (%) |
|---|---|---|---|---|---|
| M3x0.5 | 0.5 | 2.5 | 2.5 | 2.5 | 77 |
| M4x0.7 | 0.7 | 3.3 | 3.3 | 3.3 | 77 |
| M5x0.8 | 0.8 | 4.2 | 4.2 | 4.2 | 77 |
| M6x1 | 1 | 5 | 5.0 | 5 | 77 |
| M8x1.25 | 1.25 | 6.75 | 6.7 | 6.7 | 80 |
| M10x1.5 | 1.5 | 8.5 | 8.5 | 8.5 | 77 |
| M12x1.75 | 1.75 | 10.25 | 10.2 | 10.2 | 79 |
| M14x2 | 2 | 12 | 12.0 | 12 | 77 |
| M16x2 | 2 | 14 | 14.0 | 14 | 77 |
| M20x2.5 | 2.5 | 17.5 | 17.5 | 17.5 | 77 |
Source: The Cutting Speed app's engine test cases for tap drill sizes.
| Surface speed (SFM) | 1/4 in | 1/2 in | 1 in | 2 in |
|---|---|---|---|---|
| 60 | 917 | 458 | 229 | 115 |
| 100 | 1528 | 764 | 382 | 191 |
| 250 | 3820 | 1910 | 955 | 477 |
Source: Formula RPM = 12 x SFM / (pi x D), re-checked against 86 inch test cases for spindle speed in the app's engine.
Formulas
- Tap drill, about 75 percent thread
- metric: drill = major diameter - pitch inch: drill = major diameter - 1 / threads per inch
- M8x1.25: 8 - 1.25 = 6.75 mm. The chart then picks the nearest drill that exists.
- Spindle speed (inch)
- RPM = 12 x SFM / (pi x diameter in inches)
- SFM is surface feet per minute.
- Spindle speed (metric)
- RPM = 1000 x Vc / (pi x diameter in mm)
- Vc is cutting speed in metres per minute.
- Feed rate
- feed = RPM x chip load per tooth x number of teeth
Worked example
M8x1.25 and a 1/2 inch cutter
- The formula drill for M8x1.25 is 8 - 1.25 = 6.75 mm. There is no 6.75 mm drill in the usual sets, so the chart gives the nearest sizes: 6.7 mm gives a tighter hole (more thread, about 80 percent) and 6.8 mm a looser one (about 74 percent).
- A 1/2 inch end mill at 100 SFM: RPM = 12 x 100 / (pi x 0.5) = 764 RPM.
- The same cutter at 250 SFM runs at 1,910 RPM. These are starting values: take the tool maker's recommendation for your material.
Things to watch
- The thread percentage in the chart is that of the nominal thread. A maker's own table may quote the percentage of the oversize hole, which gives different numbers.
- Use a tighter drill (a higher thread percentage) only in soft material and where the extra strength is needed; in hard or gummy materials a looser drill protects the tap.
Related guide: Milling feed rate calculator: feed, chip load and spindle speed · Bolt circle calculator: hole coordinates and chord spacing · Cutting speed calculator: spindle RPM from SFM or m/min · Three-wire thread measurement: best wire size and measurement over wires · Taper per foot calculator: taper, half angle and diameters · Sine bar calculator: gauge block stack height for an angle · Tap drill size for 50, 65 and 75 percent thread
Skip the arithmetic
Cutting Speed, Tap Drill, Sine
Spindle RPM and feed, the tap drill from a drill maker's table, bolt circles and shop geometry for the machinist. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
What is the tap drill for M8x1.25?
Formula: 8 - 1.25 = 6.75 mm. The chart drill is 6.7 mm, which gives about 80 percent thread. A 6.8 mm drill is the nearest looser choice, at about 74 percent.
What is the tap drill for 1/4-20?
A #7 drill (5.105 mm), which gives about 75 percent thread. The chart lists the common inch threads with the drill and the thread percentage it gives.
