Reference guide · Machinist speeds, tap drills and shop geometry
Milling feed rate calculator: feed, chip load and spindle speed
By the Mirage Interactive team · Last checked
Feed rate is how fast the table moves the work past the cutter. It is set from three numbers: how fast the spindle turns, how many teeth the cutter has, and how thick a chip each tooth should take. Get the chip load wrong and the cutter either rubs and wears, or breaks.
This page starts from the spindle speed and ends at the feed, in inches or in millimetres. The chip load itself comes from the tool maker for your cutter and material; the tables here show what each chip load means at a given RPM, they do not say which one to use. For the spindle speed formula and tap drills, see the tap drill chart guide linked below.
The short answer
Feed rate = RPM x number of teeth x chip load per tooth. In inches the feed is in inches per minute, in millimetres it is in mm per minute.
A 1/2 inch four-flute end mill at 100 SFM turns at 763.944 RPM. At a chip load of 0.002 inch per tooth the feed is 6.1116 inches per minute (155.2 mm per minute).
Tables
The first two tables give the feed for a four-flute cutter by RPM and chip load per tooth, in inches per minute and in millimetres per minute. The third gives the feed for the 1/2 inch cutter of the worked example at 100 SFM, by number of flutes and chip load. Use your browser's print command to print this page: the tables print without the navigation.
| RPM | 0.001 | 0.002 | 0.003 | 0.004 | 0.005 |
|---|---|---|---|---|---|
| 500 | 2.0 | 4.0 | 6.0 | 8.0 | 10.0 |
| 1000 | 4.0 | 8.0 | 12.0 | 16.0 | 20.0 |
| 2000 | 8.0 | 16.0 | 24.0 | 32.0 | 40.0 |
| 3000 | 12.0 | 24.0 | 36.0 | 48.0 | 60.0 |
| 5000 | 20.0 | 40.0 | 60.0 | 80.0 | 100.0 |
| 8000 | 32.0 | 64.0 | 96.0 | 128.0 | 160.0 |
| 10000 | 40.0 | 80.0 | 120.0 | 160.0 | 200.0 |
Source: computed by the site build from the formulas below.
| RPM | 0.025 | 0.05 | 0.075 | 0.10 | 0.125 |
|---|---|---|---|---|---|
| 500 | 50 | 100 | 150 | 200 | 250 |
| 1000 | 100 | 200 | 300 | 400 | 500 |
| 2000 | 200 | 400 | 600 | 800 | 1000 |
| 3000 | 300 | 600 | 900 | 1200 | 1500 |
| 5000 | 500 | 1000 | 1500 | 2000 | 2500 |
| 8000 | 800 | 1600 | 2400 | 3200 | 4000 |
| 10000 | 1000 | 2000 | 3000 | 4000 | 5000 |
Source: computed by the site build from the formulas below.
| Flutes | 0.001 | 0.002 | 0.003 | 0.004 |
|---|---|---|---|---|
| 1 | 0.76 | 1.53 | 2.29 | 3.06 |
| 2 | 1.53 | 3.06 | 4.58 | 6.11 |
| 3 | 2.29 | 4.58 | 6.88 | 9.17 |
| 4 | 3.06 | 6.11 | 9.17 | 12.22 |
| 5 | 3.82 | 7.64 | 11.46 | 15.28 |
| 6 | 4.58 | 9.17 | 13.75 | 18.33 |
Source: computed by the site build from the formulas below.
Formulas
- Spindle speed
- RPM = 12 x SFM / ( pi x diameter in inches ) RPM = 1000 x Vc / ( pi x diameter in mm )
- SFM is surface feet per minute; Vc is cutting speed in metres per minute.
- Feed rate
- feed = RPM x teeth x chip load per tooth
- Use inches per tooth for inches per minute and millimetres per tooth for millimetres per minute. Feed per revolution is teeth x chip load.
- Reverse: chip load and surface speed
- chip load = feed / ( RPM x teeth ) SFM = pi x diameter in inches x RPM / 12
- Use them to check a feed you were given, or the surface speed that a spindle speed really gives.
Worked example
A 1/2 inch four-flute end mill at 100 SFM and 0.002 inch per tooth
- RPM = 12 x 100 / ( pi x 0.5 ) = 763.944.
- Feed = 763.944 x 4 x 0.002 = 6.1116 inches per minute, which is 155.2 mm per minute.
- Check: chip load = 6.1116 / ( 763.944 x 4 ) = 0.002 inch per tooth.
- A 1 inch cutter at 3,820 RPM runs at pi x 1 x 3820 / 12 = 1000.07 SFM.
- In metric, 30 m/min on a 10 mm cutter is 1000 x 30 / ( pi x 10 ) = 955 RPM.
Things to watch
- The numbers here are the arithmetic only. The chip load, the speed and the depth of cut depend on the cutter, the material, the machine and the setup: take them from the tool maker.
- Feed gets limited by the machine long before the formula runs out. A high RPM with a small chip load can ask for a feed that the machine cannot reach, and a low RPM can leave the cutter rubbing.
- Slotting and heavy cuts may need a reduced chip load. This page does not say which, and does not say a feed is safe.
Related guide: Tap drill chart and cutting speed (RPM) formula
More from this family: Bolt circle calculator: hole coordinates and chord spacing · Cutting speed calculator: spindle RPM from SFM or m/min · Three-wire thread measurement: best wire size and measurement over wires · Taper per foot calculator: taper, half angle and diameters · Sine bar calculator: gauge block stack height for an angle · Tap drill size for 50, 65 and 75 percent thread
Skip the arithmetic
Cutting Speed, Tap Drill, Sine
Cutting Speed, Tap Drill, Sine gives spindle RPM from cutting speed and diameter, feed rate from chip load and number of teeth, in metric or inch, with every step shown. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do you calculate the feed rate for milling?
Multiply the spindle speed in RPM by the number of teeth and by the chip load per tooth. The result is in inches per minute or millimetres per minute, depending on the chip load unit.
What is the feed rate for a 1/2 inch four-flute end mill at 100 SFM?
The spindle runs at 763.944 RPM. At 0.002 inch per tooth the feed is 6.1116 inches per minute, which is 155.2 mm per minute.
What is chip load?
The thickness of the chip that each tooth cuts: the feed per revolution divided by the number of teeth. It is the number a tool maker gives for a cutter and material.
