Reference guide · Machinist speeds, tap drills and shop geometry
Taper per foot calculator: taper, half angle and diameters
By the Mirage Interactive team · Last checked
A taper changes diameter along the length. The shop quotes it as taper per foot, inches of diameter change in each 12 inches of length, or as a ratio such as 1 : 20, or as an angle for a compound rest or a taper attachment. They are the same number in three forms, and this guide moves between them.
The tables give the angle and the ratio for common tapers per foot, and the taper per foot for common half angles. The worked examples find the taper from the two diameters and the length, and the small end from a taper per foot.
The short answer
Taper per foot = 12 x (D - d) / L, with D the large diameter, d the small diameter and L the length, all in inches. The half angle is arctan((D - d) / (2 x L)), and the included angle is twice that.
A taper from 1.000 in to 0.750 in over 3.000 in is 1.000 inch per foot, a half angle of 2.3859 degrees and an included angle of 4.7719 degrees.
Tables
The first table gives the ratio, the half angle, the included angle and the change per 100 units of length for common tapers per foot. The second gives the taper per foot and the ratio for a half angle, which is the angle to set on a compound rest. Use your browser's print command to print this page: the tables print without the navigation.
| Taper per foot (in) | Ratio 1 : x | Half angle (deg) | Included angle (deg) | Change per 100 units |
|---|---|---|---|---|
| 0.125 | 1 : 96.00 | 0.2984 | 0.5968 | 1.042 |
| 0.250 | 1 : 48.00 | 0.5968 | 1.1936 | 2.083 |
| 0.500 | 1 : 24.00 | 1.1935 | 2.3870 | 4.167 |
| 0.600 | 1 : 20.00 | 1.4321 | 2.8642 | 5.000 |
| 0.750 | 1 : 16.00 | 1.7899 | 3.5798 | 6.250 |
| 1.000 | 1 : 12.00 | 2.3859 | 4.7719 | 8.333 |
| 1.250 | 1 : 9.60 | 2.9815 | 5.9629 | 10.417 |
| 1.500 | 1 : 8.00 | 3.5763 | 7.1527 | 12.500 |
| 2.000 | 1 : 6.00 | 4.7636 | 9.5273 | 16.667 |
| 2.500 | 1 : 4.80 | 5.9469 | 11.8937 | 20.833 |
| 3.000 | 1 : 4.00 | 7.1250 | 14.2500 | 25.000 |
| 3.500 | 1 : 3.43 | 8.2971 | 16.5943 | 29.167 |
Source: computed by the site build from the formulas below.
| Half angle (deg) | Included angle (deg) | Taper per foot (in) | Ratio 1 : x |
|---|---|---|---|
| 0.25 | 0.50 | 0.1047 | 1 : 114.59 |
| 0.50 | 1.00 | 0.2094 | 1 : 57.29 |
| 1.00 | 2.00 | 0.4189 | 1 : 28.64 |
| 1.50 | 3.00 | 0.6285 | 1 : 19.09 |
| 2.00 | 4.00 | 0.8381 | 1 : 14.32 |
| 3.00 | 6.00 | 1.2578 | 1 : 9.54 |
| 4.00 | 8.00 | 1.6782 | 1 : 7.15 |
| 5.00 | 10.00 | 2.0997 | 1 : 5.72 |
| 7.50 | 15.00 | 3.1597 | 1 : 3.80 |
| 10.00 | 20.00 | 4.2318 | 1 : 2.84 |
| 15.00 | 30.00 | 6.4308 | 1 : 1.87 |
Source: computed by the site build from the formulas below.
Formulas
- Taper ratio
- c = (D - d) / L
- The change in diameter per unit of length. Every other form below follows from c, so the units of D, d and L only need to match each other.
- Taper per foot
- taper per foot = 12 x c = 12 x (D - d) / L
- In inches per foot when L is in inches. 3.5 inches per foot is the same as 7 : 24.
- Half and included angle
- half angle = arctan(c / 2) included angle = 2 x arctan(c / 2)
- The half angle is the angle between the axis and the surface, the setting for a compound rest or a taper attachment. The included angle is the angle between the two sides.
- Ratio from a half angle
- c = 2 x tan(half angle)
- Multiply by 12 for taper per foot.
- The missing diameter
- d = D - c x L D = d + c x L
- Find the small end from the large end, the taper and the length, or the other way round.
Worked example
Find a taper, find a small end and set the half angle
- Large end 1.000 in, small end 0.750 in, length 3.000 in: c = 0.250 / 3.000 = 0.08333. Taper per foot = 12 x c = 1.000 inch per foot, a ratio of 1 : 12.00.
- The half angle is arctan(0.08333 / 2) = 2.3859 degrees (2 degrees 23.16 minutes). That is the angle to set on the compound rest, measured from the axis. The included angle is 4.7719 degrees.
- A 1.5 inch per foot taper with a large end of 2.000 in over a length of 4.000 in: c = 1.5 / 12 = 0.125, so the small end is 2.000 - 0.125 x 4.000 = 1.500 in.
- In millimetres: a taper from 30 mm to 24 mm over 50 mm has c = 6 / 50 = 0.120, or 1 : 8.33, and a half angle of 3.4336 degrees.
- From an angle: a half angle of 3 degrees is c = 2 x tan 3 degrees = 0.10482, which is 1.2578 inch per foot.
Things to watch
- Taper per foot is the change in diameter, not in radius. A taper that quotes the change per side is half the diameter figure.
- The half angle is measured from the axis. A compound rest set from the cross-slide, or marked from the cross-feed axis, reads a different angle, so check which way your scale reads.
- Names of standard tapers differ by system and by size. Take the taper of a named standard from its specification and use this page for the arithmetic.
- Check a turned taper with a gauge or a sine bar. See the sine bar guide linked below.
Related guide: Tap drill chart and cutting speed (RPM) formula
More from this family: Milling feed rate calculator: feed, chip load and spindle speed · Bolt circle calculator: hole coordinates and chord spacing · Cutting speed calculator: spindle RPM from SFM or m/min · Three-wire thread measurement: best wire size and measurement over wires · Sine bar calculator: gauge block stack height for an angle · Tap drill size for 50, 65 and 75 percent thread
Skip the arithmetic
Cutting Speed, Tap Drill, Sine
Cutting Speed, Tap Drill, Sine does taper from the diameters and the length, from a taper per foot or from an angle, next to sine bar, thread wires, dovetail, chord and radius and triangles, and does spindle speed, feed and tap drills too. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do you calculate taper per foot?
Subtract the small diameter from the large one, multiply by 12 and divide by the length in inches. A 1.000 to 0.750 in taper over 3.000 in is 1.000 inch per foot.
How do you convert taper per foot to degrees?
Divide by 12 to get the ratio c, then take arctan(c / 2) for the half angle. One inch per foot is a half angle of 2.3859 degrees.
What angle do I set on a compound rest for a taper?
The half angle, measured from the axis of the work. Check the direction of your compound rest scale.
