Skip to content

Reference guide · Machinist speeds, tap drills and shop geometry

Bolt circle calculator: hole coordinates and chord spacing

By the Mirage Interactive team · Last checked

A bolt circle, also called a pitch circle diameter or PCD, is the circle that passes through the centres of a ring of holes. To drill the holes on a mill or lay them out by hand you need either the coordinates of each hole, or the straight distance between neighbouring holes to step off with dividers or calipers.

Both follow from the circle diameter and the number of holes. This page gives the formulas, a chord table for 3 to 24 holes, and the full coordinate list for a six-hole and a five-hole pattern.

The short answer

Hole k sits at x = centre x + (D / 2) x cos(start angle + 360 x (k - 1) / n) and y = centre y + (D / 2) x sin(the same angle). The distance between neighbouring holes is D x sin(180 / n).

For six holes the chord equals the radius: a 4 inch (101.6 mm) circle has holes 2 inches (50.8 mm) apart. Five holes give 0.58779 times the diameter, seven give 0.43388 and eight give 0.38268.

Tables

The first table gives the angle step and the chord between neighbouring holes for 3 to 24 holes, as a fraction of the diameter and for a 100 mm and a 4 inch circle. The second lists the six holes of a 4 inch circle. The third lists five holes on a 100 mm circle with the first hole at 90 degrees. Use your browser's print command to print this page: the tables print without the navigation.

Angle step and chord between neighbouring holes, by number of holes
HolesStep angle (deg)Chord / diameterChord on 100 mm circle (mm)Chord on 4 in circle (in)
3120.000.8660386.6033.4641
490.000.7071170.7112.8284
572.000.5877958.7792.3511
660.000.5000050.0002.0000
751.430.4338843.3881.7355
845.000.3826838.2681.5307
940.000.3420234.2021.3681
1036.000.3090230.9021.2361
1230.000.2588225.8821.0353
1622.500.1950919.5090.7804
2415.000.1305313.0530.5221

Source: computed by the site build from the formulas below.

Six holes on a 4 inch (101.6 mm) circle, centre at 0, 0, first hole at 0 degrees: coordinates in inches and millimetres
HoleAngle (deg)X (in)Y (in)X (mm)Y (mm)
102.00000.000050.80000.0000
2601.00001.732125.400043.9941
3120-1.00001.7321-25.400043.9941
4180-2.00000.0000-50.80000.0000
5240-1.0000-1.7321-25.4000-43.9941
63001.0000-1.732125.4000-43.9941

Source: computed by the site build from the formulas below.

Five holes on a 100 mm circle, centre at 0, 0, first hole at 90 degrees: coordinates in millimetres
HoleAngle (deg)X (mm)Y (mm)
1900.00050.000
2162-47.55315.451
3234-29.389-40.451
430629.389-40.451
537847.55315.451

Source: computed by the site build from the formulas below.

Formulas

Hole coordinates
x = cx + (D / 2) x cos(a0 + 360 x (k - 1) / n) y = cy + (D / 2) x sin(a0 + 360 x (k - 1) / n)
D is the circle diameter, n the number of holes, a0 the angle of the first hole measured counter-clockwise from the X axis, and cx, cy the centre of the circle.
Chord between neighbouring holes
chord = D x sin( 180 / n )
Use it to step off the holes with dividers, or to check a drilled pattern with calipers. The chord is a straight line, not the arc.
Step angle
step = 360 / n
The holes are evenly spaced, so each sits one step angle past the one before.

Worked example

Six holes on a 4 inch circle

  1. The radius is 4 / 2 = 2 inches, which is 50.8 mm, and the step angle is 360 / 6 = 60 degrees.
  2. Hole 1 is at ( 2.0000, 0.0000 ) inches, which is ( 50.8, 0.0 ) mm.
  3. Hole 2 is at ( 2 x cos 60, 2 x sin 60 ) = ( 1.0000, 1.7321 ) inches, which is ( 25.4, 43.9941 ) mm.
  4. Hole 4 is at ( -2.0000, 0.0000 ) inches, opposite hole 1, and hole 6 is at ( 1.0000, -1.7321 ).
  5. The chord is 4 x sin 30 = 2.0000 inches, which is 50.8 mm. Six holes always have a chord equal to the radius.

Things to watch

  • The coordinates are exact positions of hole centres. Which way round you number the holes, and where the first one starts, is your choice: change the start angle to rotate the whole pattern.
  • To offset the pattern from the origin, add the centre coordinates to every X and Y. Backlash and tolerance are not included.
  • Check a printed template against a ruler before you drill, and try it on scrap. This page does not say that a hole position is within tolerance.

Related guide: Tap drill chart and cutting speed (RPM) formula

More from this family: Milling feed rate calculator: feed, chip load and spindle speed · Cutting speed calculator: spindle RPM from SFM or m/min · Three-wire thread measurement: best wire size and measurement over wires · Taper per foot calculator: taper, half angle and diameters · Sine bar calculator: gauge block stack height for an angle · Tap drill size for 50, 65 and 75 percent thread

Skip the arithmetic

Cutting Speed, Tap Drill, Sine

Cutting Speed, Tap Drill, Sine gives bolt circle coordinates and a 1:1 printable drilling template, and spindle RPM and feed for the cutter that drills them. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

How do you calculate the hole positions on a bolt circle?

Put hole k at the angle start + 360 x (k - 1) / n round the circle, then x = (D / 2) cos(angle) and y = (D / 2) sin(angle), plus the centre coordinates.

What is the distance between holes on a six-hole bolt circle?

Equal to the radius, so 2 inches on a 4 inch circle, 50 mm on a 100 mm circle.

What is the chord factor for five holes?

0.58779 times the circle diameter, which is sin 36 degrees.