Reference guide · EMT conduit bending marks
Conduit rolling offset calculator: marks, shrink and roll angle
By the Mirage Interactive team · Last checked
A rolling offset takes conduit around an obstacle that is both above and to one side of the run, such as a pipe that sits up and over. You still make two bends of the same angle, but the second is rotated round the conduit by the roll angle so the line ends up in the right place in both directions.
The marks come from one number, the true offset, which combines the rise and the roll. This page shows how to find it, the marks and shrink that follow, and the roll angle to rotate the conduit by. The flat offset multipliers are in the conduit multiplier guide linked below.
The short answer
True offset = square root of (rise squared + roll squared). Distance between the two marks = true offset x multiplier (1.4142 at 45 degrees, 2 at 30, 2.6131 at 22.5). Shrink = true offset x tan(angle / 2).
Rise 12 and roll 9 make a true offset of 15.0 inches. At 45 degrees the marks are 21.2132 inches apart, the shrink is 6.2132 inches and the roll angle is 36.87 degrees.
Tables
The first table gives the true offset for the rise (rows) and the roll (columns) in inches. The second gives the distance between the marks and the shrink for a true offset at three bend angles. Use your browser's print command to print this page: the tables print without the navigation.
| Rise (in) / roll (in) | 2 | 3 | 4 | 6 | 8 | 10 | 12 |
|---|---|---|---|---|---|---|---|
| 2 | 2.83 | 3.61 | 4.47 | 6.32 | 8.25 | 10.20 | 12.17 |
| 3 | 3.61 | 4.24 | 5.00 | 6.71 | 8.54 | 10.44 | 12.37 |
| 4 | 4.47 | 5.00 | 5.66 | 7.21 | 8.94 | 10.77 | 12.65 |
| 6 | 6.32 | 6.71 | 7.21 | 8.49 | 10.00 | 11.66 | 13.42 |
| 8 | 8.25 | 8.54 | 8.94 | 10.00 | 11.31 | 12.81 | 14.42 |
| 10 | 10.20 | 10.44 | 10.77 | 11.66 | 12.81 | 14.14 | 15.62 |
| 12 | 12.17 | 12.37 | 12.65 | 13.42 | 14.42 | 15.62 | 16.97 |
Source: computed by the site build from the formulas below.
| True offset (in) | 22.5: marks apart | 22.5: shrink | 30: marks apart | 30: shrink | 45: marks apart | 45: shrink |
|---|---|---|---|---|---|---|
| 3 | 7.84 | 0.60 | 6.00 | 0.80 | 4.24 | 1.24 |
| 4 | 10.45 | 0.80 | 8.00 | 1.07 | 5.66 | 1.66 |
| 5 | 13.07 | 0.99 | 10.00 | 1.34 | 7.07 | 2.07 |
| 6 | 15.68 | 1.19 | 12.00 | 1.61 | 8.49 | 2.49 |
| 8 | 20.91 | 1.59 | 16.00 | 2.14 | 11.31 | 3.31 |
| 10 | 26.13 | 1.99 | 20.00 | 2.68 | 14.14 | 4.14 |
| 12 | 31.36 | 2.39 | 24.00 | 3.22 | 16.97 | 4.97 |
| 15 | 39.20 | 2.98 | 30.00 | 4.02 | 21.21 | 6.21 |
| 20 | 52.26 | 3.98 | 40.00 | 5.36 | 28.28 | 8.28 |
Source: computed by the site build from the formulas below.
Formulas
- True offset and roll angle
- true offset = sqrt( rise^2 + roll^2 ) roll angle = arctan( roll / rise )
- The roll angle is how far to rotate the conduit between the two bends, measured from the rise direction. With a 12 inch rise and a 9 inch roll it is 36.87 degrees; with a 9 inch rise and a 12 inch roll it is 53.13 degrees.
- Marks
- distance between marks = true offset / sin(angle) shrink = true offset x tan(angle / 2)
- Measure both marks from the end of the conduit. Add the shrink to the length you cut.
- Trade multipliers
- exact: 1.4142 and 0.4142 trade: 1.4 and 3/8
- At 45 degrees many charts round the marks multiplier to 1.4 and the shrink to 3/8 inch per inch of offset. The exact values are shown here so that you can see the difference.
Worked example
A 12 inch rise and a 9 inch roll at 45 degrees
- True offset = square root of ( 12 squared + 9 squared ) = 15.0 inches.
- The roll angle is arctan( 9 / 12 ) = 36.87 degrees: rotate the conduit that much between the two bends.
- Distance between the marks = 15.0 x 1.4142 = 21.2132 inches. If the first mark is 10 inches from the end, the second is at 31.2132 inches.
- Shrink = 15.0 x tan 22.5 = 6.2132 inches, so cut the conduit that much longer.
- With the trade multipliers, 1.4 x 15.0 = 21.0 inches between the marks and 3/8 x 15.0 = 5.625 inches of shrink, which is 0.588 inch less than the exact figure.
Things to watch
- Which reference of your bender you line each mark up with depends on the tool. Use your own bender values.
- Bend one piece of scrap first and check it against the obstacle before you bend the run: rotating by the roll angle is the step that is easiest to get wrong.
- This page gives geometry only. It does not say a layout meets any electrical code.
Related guide: Conduit bending multipliers and offset chart
More from this family: 3-point and 4-point saddle bend calculator · Conduit bending offset chart in metric: multipliers and shrink in mm · 90 degree stub-up in conduit: take-up chart and back-to-back marks · Voltage drop calculator: drop in volts and percent for a copper or aluminium run · Wire size calculator: AWG sizes and the smallest size for a voltage drop target
Skip the arithmetic
Conduit Bending & Offset Marks
Conduit Bending & Offset Marks does rolling offsets with the true offset and roll angle, lists the marks in order, measured from the end of the conduit, with the shrink you will lose, and lets you choose trade-table multipliers or exact geometry. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do you find the marks for a rolling offset in conduit?
Find the true offset, the square root of the rise squared plus the roll squared, then multiply it by the multiplier for your bend angle to get the distance between the two marks.
What roll angle do I use?
The angle whose tangent is the roll divided by the rise. A 12 inch rise with a 9 inch roll is 36.87 degrees.
Is the shrink the same as for a flat offset?
Yes, for the same true offset and angle: the true offset times tan(angle / 2), so 6.2132 inches for 15 inches at 45 degrees.
