Skip to content

Reference guide · EMT conduit bending marks

90 degree stub-up in conduit: take-up chart and back-to-back marks

By the Mirage Interactive team · Last checked

A stub-up is the short straight piece left standing at the end of conduit after a 90 degree bend. The bender uses up some length in the bend, so the mark is not put at the height you want. It goes back from the end of the conduit by the take-up of your bender, and the arrow or star of the bender is lined up with it.

The take-up is a number for the bender and the conduit size: it is stamped on the bender, or listed in its chart. This page assumes you know it, and gives the marks that follow for stub heights, plus the second mark when two 90 degree bends are made back to back.

The short answer

Mark = stub height - take-up, measured from the end of the conduit. A 12 inch stub with a 5 inch take-up is marked at 7 inches; with a 6 inch take-up at 6 inches; with an 8 inch take-up at 4 inches.

For back-to-back 90s, cut length = first leg + second leg - gain. The gain is also a number for the bender.

Tables

The first table gives the mark in inches for stub heights from 10 to 30 inches and take-ups of 5, 6 and 8 inches. The second gives the second mark from the end of the conduit for back-to-back 90s with a 2 inch gain. Use your browser's print command to print this page: the tables print without the navigation.

Mark (in), measured from the end of the conduit, by stub height and bender take-up
Stub height (in)Take-up 5 inTake-up 6 inTake-up 8 in
10542
12764
14986
1611108
18131210
20151412
24191816
30252422

Source: computed by the site build from the formulas below.

Back-to-back 90s: second mark (in) from the end of the conduit, by the first leg (rows) and the distance between the backs of the bends (columns), gain 2 in
First leg (in) / between (in)243036
12344046
18404652
24465258

Source: computed by the site build from the formulas below.

Formulas

Stub-up mark
mark = stub height - take-up
Measured from the end of the conduit. The stub height has to be longer than the take-up, otherwise the bender cannot make the bend that short.
Developed length of two legs
cut length = leg A + leg B - gain
Leg A and leg B are measured to the back of the bend, as drawn. The gain is the length that the bend saves compared with running to a square corner.
Back-to-back 90s
mark 1 = first leg - take-up mark 2 from the end = first leg + between - gain
Mark 2 can also be measured on the bent conduit: the distance between the backs of the two bends, from the back of the first one.

Worked example

A 12 inch stub, then a second 90 back to back

  1. With a take-up of 5 inches the mark for a 12 inch stub is 12 - 5 = 7 inches from the end. A take-up of 6 gives 6 and a take-up of 8 gives 4.
  2. Line up the bender mark with that point and bend 90 degrees. The conduit now has a 12 inch leg measured to the back of the bend.
  3. For a second 90 degree bend 30 inches further on, back to back, with a gain of 2 inches, the second mark is 40 inches from the end of the conduit: 12 + 30 - 2.
  4. The same 40 inches is the length of conduit you need between the two legs: cut length = 12 + 30 - 2.

Things to watch

  • Take-up and gain depend on the bender and the conduit size. Use the values for your own bender; the 5, 6 and 8 inch columns are examples, not a list of bender data.
  • Bend a scrap piece first and measure the stub, to confirm that the take-up you are using is right for your own bender and conduit size.
  • This page gives geometry only. It does not say a layout meets any electrical code or check the bend radius.

Related guide: Conduit bending multipliers and offset chart

More from this family: 3-point and 4-point saddle bend calculator · Conduit bending offset chart in metric: multipliers and shrink in mm · Conduit rolling offset calculator: marks, shrink and roll angle · Voltage drop calculator: drop in volts and percent for a copper or aluminium run · Wire size calculator: AWG sizes and the smallest size for a voltage drop target

Skip the arithmetic

Conduit Bending & Offset Marks

Conduit Bending & Offset Marks does 90 stubs and back-to-back 90s with your own bender's take-up and gain, and lists the marks in order, measured from the end of the conduit. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

How do you find the mark for a 90 degree stub-up?

Subtract the take-up of your bender from the stub height you want, and measure that distance from the end of the conduit.

What is take-up in conduit bending?

The length of conduit that a 90 degree bend uses up, so that the mark goes back from the end by that amount. It is listed for each bender and conduit size.

How long should the conduit be for two 90s back to back?

The first leg plus the second leg minus the gain. For legs of 12 and 30 inches with a gain of 2 inches that is 40 inches.