Skip to content

Reference guide · Miter, crown molding and brace angles

Picture frame miter angle calculator: saw setting and cut length

By the Mirage Interactive team · Last checked

A picture frame is a ring of pieces whose ends are cut at matching angles. At each corner the two pieces meet along a line that splits the corner in half, so the saw is set to half the turn the corner makes. A four-sided frame has 90 degree corners and takes a 45 degree miter; a six-sided frame has 120 degree corners and takes 30.

The saw setting is only half the job. The pieces also have to be the right length, and the opening you measured is not the length of a piece: each end of the molding is cut at an angle, so the longest edge of the piece, the long point on the outside edge, reaches past the opening. This guide gives both numbers.

The short answer

Saw miter setting = 90 degrees minus half the corner angle, measured from a square cut. For N equal sides the corner is 180 x (N - 2) / N, which makes the setting 180 / N: 45 for 4 sides, 36 for 5, 30 for 6 and 22.5 for 8.

Long point of a piece = inside length + 2 x molding width x tan(saw miter). For a 90 degree corner that is the inside length plus twice the molding width.

Tables

The first table gives the corner angle, the saw setting and the angle on the piece for frames of 3 to 12 equal sides. The second gives how far each end of a piece reaches past the inside edge for three molding widths: add twice that figure to the inside length. Use your browser's print command to print this page: the tables print without the navigation.

A four-sided frame, where the saw miter is 45 degrees and the long point is longer than the inside length by w on each end. For other numbers of sides each end adds w × tan(saw miter), as in the formulas below.
Picture frame with equal sides: corner angle, saw miter setting and angle on the piece, in degrees
SidesCorner angle (deg)Saw miter setting (deg)Angle on the piece (deg)Past a 50 degree saw limit?
3606030Yes (60)
4904545No
51083654No
61203060No
7128.5725.7164.29No
813522.567.5No
91402070No
101441872No
11147.2716.3673.64No
121501575No

Source: computed by the site build from the formulas below.

How far each end of a piece reaches past its inside edge, in inches, by number of sides and molding width
SidesFactor: tan(saw miter)1 in molding1 1/2 in molding2 in molding
31.73211.7322.5983.464
41.00001.0001.5002.000
50.72650.7271.0901.453
60.57740.5770.8661.155
70.48160.4820.7220.963
80.41420.4140.6210.828
90.36400.3640.5460.728
100.32490.3250.4870.650
110.29360.2940.4400.587
120.26790.2680.4020.536

Source: computed by the site build from the formulas below.

Formulas

Saw setting
saw miter = 90 - corner / 2 corner of N equal sides = 180 x (N - 2) / N
Measured from a square cut, so 0 is a square cut. The angle on the piece, between the cut face and its long edge, is corner / 2.
Long point
long point = inside length + 2 x width x tan(saw miter) = inside length + 2 x width / tan(corner / 2)
Inside length is measured between the short points, on the opening side of the molding. Width is the width of the piece across its face. Saw kerf and any rabbet allowance are not included: test on scrap.
Construction check
offset every edge of the opening outward by the width, intersect neighbouring lines, measure the outer edge
This gives the same long point without a tangent, and is a quick way to check a result with a drawing.

Worked example

A rectangular frame, then a six-sided one

  1. Opening 762 x 508 mm (30 x 20 inches), molding 44 mm wide, four 90 degree corners. The saw miter setting is 90 - 90 / 2 = 45 degrees.
  2. Each end reaches 44 x tan 45 = 44 mm past the inside edge, so the long points are 762 + 88 = 850 mm and 508 + 88 = 596 mm. Cut two pieces of each.
  3. A hexagon with inside sides of 624 mm and molding 41 mm wide has 120 degree corners, so the saw miter setting is 90 - 60 = 30 degrees.
  4. Each end reaches 41 x tan 30 = 23.67 mm past the inside edge, so the long point is 624 + 47.34 = 671.34 mm. All six pieces are the same.
  5. The same rule gives 103 x 53 inches for a 100 x 50 inch opening with 1 1/2 inch molding (2616.2 x 1346.2 mm), which is a quick check on any layout.

Things to watch

  • Measure the opening the same way for every piece, on the inside (short-point) edge of the molding. A piece cut to the long point length is only right if the inside length is that measurement.
  • Many miter saws stop at about 50 degrees. A triangular frame needs 60, which is past that, so cut it with a jig or another method.
  • Saw kerf is not included. Cut a test corner from scrap and check it before you cut good molding.
  • These settings assume equal sides, or one typed corner angle with the same corner at both ends of a piece. A frame with unequal corners needs each piece worked out from its own two corners.

Related guide: Crown molding angle chart: miter and bevel settings for flat cuts

More from this family: Gate and diagonal brace angle calculator · Coving angle calculator: mitre and bevel for internal and external corners · Crown molding spring angle chart: miter and bevel by spring angle · Crown molding outside corner angles: miter and bevel settings

Skip the arithmetic

Miter Angle & Brace Calculator

Miter Angle & Brace Calculator gives the saw miter setting and the angle on the piece for a frame from the number of sides or a typed corner angle, with a warning when the setting is beyond what many saws reach. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

What angle do I cut for a picture frame?

For a rectangular frame set the saw to 45 degrees. For a frame with N equal sides, set it to 180 / N degrees: 36 for a pentagon, 30 for a hexagon and 22.5 for an octagon.

How long should I cut each piece?

Take the inside length of the opening and add twice the molding width for a 90 degree corner. That figure is the long point, the longest edge of the piece.

Why does an octagon use 22.5 degrees?

Eight corners of 135 degrees are each split in half, so the saw is set to 90 - 135 / 2 = 22.5 degrees from a square cut.