Skip to content

Reference guide · Miter, crown molding and brace angles

Crown molding outside corner angles: miter and bevel settings

By the Mirage Interactive team · Last checked

An outside corner is where two walls turn away from you, like a chimney breast or a square column. The molding wraps round the corner instead of meeting in a notch, but the geometry of the two cuts is the same as for an inside corner of the same wall angle: the saw settings do not change, only the direction each piece is turned.

That makes outside corners simpler than they look, with one trap. Measure the angle between the two walls the way you would for an inside corner (90 degrees for a square corner), look up the settings for that angle, and take the side of the blade each piece goes on from your saw's crown chart or a scrap test, because these numbers are magnitudes only.

The short answer

An outside corner of W degrees takes the settings of an inside corner of W degrees. For crown laid flat: miter = arctan( sin S / tan(W / 2) ) and bevel = arcsin( cos S x cos(W / 2) ), where S is the spring angle measured from the wall.

For S = 38 and a square (90 degree) outside corner that is 31.6 degrees of miter and 33.9 of bevel; for S = 45 it is 35.3 and 30.0. The direction of each cut is the reverse of the inside corner.

Tables

Settings for an outside corner by the angle between the two walls, at the two common spring angles, in degrees. A star marks a setting beyond what many saws reach (more than 50 degrees of miter or more than 45 of bevel). The third column is the angle through the room, 360 degrees minus the wall angle, which is what the app works on. Use your browser's print command to print this page: the tables print without the navigation.

Plan view of an outside corner. The settings use W, the angle between the walls; the app works on the room angle, 360 − W, and folds it back to W.
Crown molding laid flat, outside corner: miter and bevel by the angle between the walls, at 38 and 45 degree spring angles
Angle between the walls (deg)Typical caseAngle through the room (deg)38: miter38: bevel45: miter45: bevel
45Very sharp point31556.07*46.72*59.64*40.79
60Sharp point30046.8443.0350.77*37.76
72Sharp point28840.2839.6144.2234.89
90Square corner27031.6233.8635.2630.00
108Five-sided25224.1027.5927.1924.56
120Six-sided bay24019.5723.2022.2120.70
135Chamfered corner, eight-sided22514.3117.5516.3215.70
150Twelve-sided, gentle bend2109.3711.7710.7310.55

Source: computed by the site build from the formulas below.

Formulas

Settings for molding laid flat
miter = arctan( sin(S) / tan(W / 2) ) bevel = arcsin( cos(S) x cos(W / 2) )
S is the spring angle from the wall and W is the angle between the two walls, 90 for a square corner, inside or outside.
Outside corner to inside corner
room angle = 360 - W (outside) room angle = W (inside) settings use the smaller of the room angle and 360 minus it
A 90 degree outside corner is a 270 degree turn through the room. Folded back to 90, it has exactly the settings of a 90 degree inside corner.
Typical saw limits
miter above 50 degrees or bevel above 45 degrees is past many saws
These are the warning limits the app uses, not a rule. Check the range of your own saw.

Worked example

A 38 degree crown at a square corner, a chamfered corner and a sharp point

  1. Square outside corner, spring angle 38: the walls make 90 degrees, so W / 2 = 45 and tan 45 = 1. Miter = arctan( sin 38 ) = 31.619 degrees and bevel = arcsin( cos 38 x cos 45 ) = 33.863 degrees, the settings of a square inside corner.
  2. In the app, choose Outside corner and type 90 for the angle between the walls. It works on the room angle 360 - 90 = 270, folds it back to 90 and returns the same two numbers.
  3. A chamfered corner of 135 degrees between the walls, same molding: miter 14.31 degrees, bevel 17.55 degrees. The flatter the corner, the smaller both angles.
  4. A sharp 60 degree outside point in 45/45 molding: miter 50.77 degrees, bevel 37.76 degrees. The miter is above 50, so many saws cannot set it and the app marks the result as beyond a typical saw.

Things to watch

  • These are magnitudes. They do not say which way to swing the saw or which side of the blade each piece lies on. For an outside corner the cuts are the reverse of an inside corner; your saw's crown chart or a scrap test settles it.
  • The settings assume a flat ceiling, plumb walls and a constant spring angle. A real corner is rarely exactly 90 degrees: measure it with an angle finder or a bevel gauge and use the measured wall angle.
  • The numbers are for the flat method, with the molding lying on the saw table back down. Cutting the molding nested against the fence uses different settings.
  • Cut a test corner from scrap and hold it in place before cutting the run.

Related guide: Crown molding angle chart: miter and bevel settings for flat cuts

More from this family: Gate and diagonal brace angle calculator · Coving angle calculator: mitre and bevel for internal and external corners · Crown molding spring angle chart: miter and bevel by spring angle · Picture frame miter angle calculator: saw setting and cut length

Skip the arithmetic

Miter Angle & Brace Calculator

Miter Angle & Brace Calculator gives compound miter and bevel settings for crown molding cut flat on the saw table, from the spring angle (52/38, 45/45 or your own), inside or outside corner and the wall angle. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

Are outside corner crown molding angles different from inside corners?

The saw settings are the same for the same angle between the walls. What changes is the direction of the cuts, because each piece is turned the other way.

What are the settings for a 90 degree outside corner?

Laid flat, 31.6 degrees of miter and 33.9 degrees of bevel for 38 degree spring molding (52/38), and 35.3 and 30.0 for 45/45.

How do I enter an outside corner in the app?

Choose Outside corner and type the angle between the two walls, 90 for a square corner. The app converts it to the room angle itself.