Skip to content

Reference guide · Miter, crown molding and brace angles

Crown molding angle chart: miter and bevel settings for flat cuts

By the Mirage Interactive team · Last checked

A crown molding angle chart gives two saw settings for each corner: the miter angle and the bevel angle. They depend on only two things, the spring angle of the molding (the angle it leans out from the wall) and the angle between the two walls. This guide uses the flat method, where the molding lies face-up on the saw table with its back flat on the table.

The chart below is for inside corners. An outside corner uses the same two numbers as the inside corner with the same wall angle, with the cuts reversed. A normal 90 degree outside corner therefore takes the same settings as a 90 degree inside corner.

Printable tables

Settings for crown molding cut flat, and for picture frames. Settings above about 50 degrees of miter are beyond many saws. Use your browser's print command to print this page: the tables print without the navigation.

Crown molding cut flat, inside corners: saw settings by wall angle and spring angle
Wall corner (deg)38 deg spring: miter38 deg spring: bevel45 deg spring: miter45 deg spring: bevel
6046.843.050.837.8
7240.339.644.234.9
9031.633.935.330.0
10824.127.627.224.6
12019.623.222.220.7
13514.317.616.315.7

Source: The Miter app's engine test cases for inside corners. The closed-form formulas on this page were re-checked against all 150 of those cases (largest difference 1e-14 deg).

Picture frames and polygons: saw miter by number of sides
SidesCorner angle (deg)Saw miter setting (deg)Cut angle on the piece (deg)
3606030
4904545
51083654
61203060
7128.5725.7164.29
813522.567.5
91402070
101441872
11147.2716.3673.64
121501575

Source: The Miter app's engine test cases for picture frames and polygons.

Formulas

Crown molding, flat method
miter = arctan( sin(spring) / tan(corner / 2) ) bevel = arcsin( cos(spring) x cos(corner / 2) )
spring is the molding's spring angle (38 degrees for 52/38 crown, 45 degrees for 45/45); corner is the angle between the walls.
Picture frame or equal-sided polygon
saw miter = 180 / sides corner angle = 180 x (sides - 2) / sides
A four-sided frame has 90 degree corners and a 45 degree miter on each piece.
Brace span
span = square root of (width squared + height squared) angle from horizontal = arctan(height / width)
The span is the corner-to-corner distance, not a board cut length.

Worked example

A 90 degree inside corner in 38 degree spring crown

  1. Spring angle 38 degrees and wall corner 90 degrees. The half corner is 45 degrees, so tan 45 = 1 and cos 45 = 0.7071.
  2. Miter = arctan( sin 38 / 1 ) = arctan(0.6157) = 31.619 degrees.
  3. Bevel = arcsin( cos 38 x 0.7071 ) = arcsin(0.5572) = 33.863 degrees.
  4. For 45/45 crown the same corner gives 35.264 degrees of miter and 30.000 degrees of bevel.
  5. A hexagonal frame has six sides: miter = 180 / 6 = 30 degrees. A gate brace 600 mm wide and 800 mm high has a span of 1000 mm and sits at 53.13 degrees from horizontal.

Things to watch

  • Which way the saw swings, and which piece goes on which side of the blade, depends on your saw and on whether the molding sits upside down. Check your saw's crown chart and test on scrap first.
  • These settings assume a flat ceiling and plumb walls with a constant spring angle. Out-of-square corners need their own measured wall angle.

Related guide: Gate and diagonal brace angle calculator · Coving angle calculator: mitre and bevel for internal and external corners · Crown molding spring angle chart: miter and bevel by spring angle · Picture frame miter angle calculator: saw setting and cut length · Crown molding outside corner angles: miter and bevel settings

Skip the arithmetic

Miter Angle & Brace Calculator

Saw settings for picture frames and crown molding, and the span and angles of a gate or shelf brace, from your measurements. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

What is the miter and bevel for crown molding at 90 degrees?

For 38 degree spring crown laid flat, 31.6 degrees miter and 33.9 degrees bevel. For 45/45 crown, 35.3 degrees miter and 30.0 degrees bevel.

Does the chart work for outside corners?

Yes. An outside corner uses the settings of the inside corner with the same wall angle, with the cut directions reversed.