Reference guide · Miter, crown molding and brace angles
Crown molding spring angle chart: miter and bevel by spring angle
By the Mirage Interactive team · Last checked
The spring angle is the angle at which crown molding leans between the wall and the ceiling. It decides both saw settings when you cut the molding flat on the table. The common angles are 38 (a 52/38 molding, which meets the ceiling at 52 degrees and the wall at 38) and 45 (a 45/45 molding). Other profiles sit anywhere between 30 and 60 degrees.
This chart is the companion to our crown molding angle chart. That one is organised by wall angle for two common spring angles. This one is organised by spring angle, so you can find the settings for a molding that is neither of those, and it adds the drop and projection of each size.
The short answer
For a 90 degree inside corner, miter = arctan( sin S / 1 ) and bevel = arcsin( cos S x 0.7071 ), where S is the spring angle measured from the wall.
S = 38 gives 31.6 and 33.9 degrees. S = 45 gives 35.3 and 30.0 degrees. S = 52 gives 38.2 and 25.8 degrees.
Tables
The first table gives the settings for a 90 degree corner by spring angle, with the drop and projection factors per unit of back length. The second gives the settings for walls that are not square. The third gives the drop and projection in inches for common back lengths, with a fraction to the nearest 1/16 inch. Use your browser's print command to print this page: the tables print without the navigation.
| Spring angle from wall (deg) | Miter (deg) | Bevel (deg) | Drop on wall per unit | Projection on ceiling per unit |
|---|---|---|---|---|
| 30 (60 to ceiling) | 26.57 | 37.76 | 0.8660 | 0.5000 |
| 35 (55 to ceiling) | 29.84 | 35.40 | 0.8192 | 0.5736 |
| 38 (52 to ceiling) | 31.62 | 33.86 | 0.7880 | 0.6157 |
| 40 (50 to ceiling) | 32.73 | 32.80 | 0.7660 | 0.6428 |
| 45 (45 to ceiling) | 35.26 | 30.00 | 0.7071 | 0.7071 |
| 50 (40 to ceiling) | 37.45 | 27.03 | 0.6428 | 0.7660 |
| 52 (38 to ceiling) | 38.24 | 25.81 | 0.6157 | 0.7880 |
| 55 (35 to ceiling) | 39.32 | 23.93 | 0.5736 | 0.8192 |
| 60 (30 to ceiling) | 40.89 | 20.70 | 0.5000 | 0.8660 |
Source: computed by the site build from the formulas below.
| Wall angle (deg) | 38: miter | 38: bevel | 45: miter | 45: bevel | 52: miter | 52: bevel |
|---|---|---|---|---|---|---|
| 85 | 33.9 | 35.5 | 37.7 | 31.4 | 40.7 | 27.0 |
| 88 | 32.5 | 34.5 | 36.2 | 30.6 | 39.2 | 26.3 |
| 90 | 31.6 | 33.9 | 35.3 | 30.0 | 38.2 | 25.8 |
| 92 | 30.7 | 33.2 | 34.3 | 29.4 | 37.3 | 25.3 |
| 95 | 29.4 | 32.2 | 32.9 | 28.5 | 35.8 | 24.6 |
Source: computed by the site build from the formulas below.
| Back length (in) | 38: drop | 38: projection | 45: drop | 45: projection |
|---|---|---|---|---|
| 3.5 | 2.76 (2 3/4) | 2.15 (2 1/8) | 2.47 (2 1/2) | 2.47 (2 1/2) |
| 4.25 | 3.35 (3 3/8) | 2.62 (2 5/8) | 3.01 (3) | 3.01 (3) |
| 5.25 | 4.14 (4 1/8) | 3.23 (3 1/4) | 3.71 (3 11/16) | 3.71 (3 11/16) |
| 6.5 | 5.12 (5 1/8) | 4.00 (4) | 4.60 (4 5/8) | 4.60 (4 5/8) |
| 8 | 6.30 (6 5/16) | 4.93 (4 15/16) | 5.66 (5 11/16) | 5.66 (5 11/16) |
Source: computed by the site build from the formulas below.
Formulas
- Settings for molding laid flat
- miter = arctan( sin(S) / tan(E / 2) ) bevel = arcsin( cos(S) x cos(E / 2) )
- S is the spring angle from the wall and E is the angle between the two walls. The molding lies flat on the table, back down.
- Spring angle from a measurement
- S = arctan( projection / drop )
- Hold the molding in place or against a square. Drop is how far it covers the wall, projection how far it reaches across the ceiling, both to the outer edges.
- Drop and projection
- drop = L x cos(S) projection = L x sin(S)
- L is the back length, which is the straight line between the two outer edges of the back. Use it to check the molding against the wall and ceiling space you have.
Worked example
A 5 1/4 inch molding at 52/38 in a 92 degree corner
- The spring angle from the wall is 38 degrees. For a 5.25 inch back length the drop is 5.25 x cos 38 = 4.14 inches and the projection is 5.25 x sin 38 = 3.23 inches.
- The corner is 92 degrees, so E / 2 = 46 degrees.
- Miter = arctan( sin 38 / tan 46 ) = 30.7 degrees.
- Bevel = arcsin( cos 38 x cos 46 ) = 33.2 degrees.
- For comparison, the same molding in a 90 degree corner needs 31.6 degrees of miter and 33.9 degrees of bevel.
Things to watch
- The turn of the saw head and the side of the blade you place the piece on depend on your saw and on which piece you are cutting. Check against your saw chart and cut a scrap first.
- Many saws stop around 50 degrees of miter and 45 to 48 of bevel. If the setting you need is past that, cut the molding on edge in a jig or use a different method.
- A spring angle read from a catalogue is only as good as the profile. Measure your own molding where you can, since two profiles of the same nominal size can lean differently.
Related guide: Crown molding angle chart: miter and bevel settings for flat cuts
More from this family: Gate and diagonal brace angle calculator · Coving angle calculator: mitre and bevel for internal and external corners · Picture frame miter angle calculator: saw setting and cut length · Crown molding outside corner angles: miter and bevel settings
Skip the arithmetic
Miter Angle & Brace Calculator
Miter Angle & Brace Calculator gives compound miter and bevel settings for crown molding cut flat on the saw table, from the spring angle (52/38, 45/45 or your own), inside or outside corner and the wall angle. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
What is the spring angle of crown molding?
It is the angle between the back of the molding and the wall. 52/38 molding has a spring angle of 38 degrees from the wall, and 45/45 molding has 45 degrees.
What are the settings for 52/38 crown in a square corner?
Laid flat, 31.6 degrees of miter and 33.9 degrees of bevel.
Does the size of the molding change the settings?
No. Only the spring angle and the wall angle do. The size changes the drop and projection, which is why the third table is separate.
