Reference guide · Miter, crown molding and brace angles
Gate and diagonal brace angle calculator
By the Mirage Interactive team · Last checked
A diagonal brace stops a gate, a frame or a shelf from racking. Its span is the corner-to-corner distance of the rectangle it crosses, and its angle follows from the width and height. Both come from a right triangle.
The span is not the length of the board you cut. The cut length depends on the board width and how the ends meet the frame, so treat the span as the starting number and check with the actual board.
The short answer
span = square root of (width squared + height squared). Angle from horizontal = arctan(height / width). Angle from vertical = 90 degrees minus that.
Example from the app: 23 5/8 x 31 1/2 inches gives a span of 39 3/8 inches at 53.1 degrees from horizontal and 36.9 degrees from vertical.
Tables
Span and angles for common gate and frame sizes in inches. For other sizes use the formula below. Use your browser's print command to print this page: the tables print without the navigation.
| Width x height (in) | Span (in) | Span (nearest 1/16) | From horizontal (deg) | From vertical (deg) |
|---|---|---|---|---|
| 24 x 24 | 33.94 | 33 15/16 | 45.0 | 45.0 |
| 30 x 36 | 46.86 | 46 7/8 | 50.2 | 39.8 |
| 36 x 36 | 50.91 | 50 15/16 | 45.0 | 45.0 |
| 36 x 48 | 60.00 | 60 | 53.1 | 36.9 |
| 42 x 48 | 63.78 | 63 3/4 | 48.8 | 41.2 |
| 48 x 48 | 67.88 | 67 7/8 | 45.0 | 45.0 |
| 48 x 60 | 76.84 | 76 13/16 | 51.3 | 38.7 |
| 60 x 72 | 93.72 | 93 3/4 | 50.2 | 39.8 |
Source: computed by the site build from the formulas below.
| Measured at | Width x height (in) | Span (in) | From horizontal (deg) |
|---|---|---|---|
| Inside edges | 36.0 x 48.0 | 60.00 | 53.1 |
| Centre lines | 39.5 x 51.5 | 64.90 | 52.5 |
| Outside edges | 43.0 x 55.0 | 69.81 | 52.0 |
Source: computed by the site build from the formulas below.
Formulas
- Brace span and angles
- span = square root of (width squared + height squared) from horizontal = arctan(height / width) from vertical = arctan(width / height)
- The span is the corner-to-corner distance, not a board cut length.
- Moving between inside, centre line and outside
- centre line = inside + member width outside = inside + 2 x member width
- Add the width of the frame members to both the width and the height.
Worked example
A gate 23 5/8 by 31 1/2 inches
- Width 23.625 inches and height 31.5 inches.
- Span = square root of (23.625^2 + 31.5^2) = square root of 1550.39 = 39.375 inches, which is 39 3/8 inches to the nearest 1/16.
- Angle from horizontal = arctan(31.5 / 23.625) = 53.13 degrees. Angle from vertical = 36.87 degrees.
- The board angle you set on the saw is one of these two angles, depending on which face you reference. Check the ends against the frame before cutting good timber.
Things to watch
- Measure the same way for width and height: both inside, both on the centre lines or both outside. Mixing them gives the wrong angle.
- The span is the distance between two corners. The board for a brace between members is shorter or longer depending on how it is fitted.
- Test on scrap before cutting good material. This is geometry only and does not say a brace is strong enough.
Related guide: Crown molding angle chart: miter and bevel settings for flat cuts
More from this family: Coving angle calculator: mitre and bevel for internal and external corners · Crown molding spring angle chart: miter and bevel by spring angle · Picture frame miter angle calculator: saw setting and cut length · Crown molding outside corner angles: miter and bevel settings
Skip the arithmetic
Miter Angle & Brace Calculator
Miter Angle & Brace Calculator takes the width and height, gives the span and the angles from horizontal and from vertical, and lets you choose whether you measured the inside, the outside or the center lines. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
What angle should a gate brace be?
It follows from the gate size. For a square gate it is 45 degrees. For a gate 36 wide and 48 high it is 53.1 degrees from horizontal.
Which way should the brace run?
On a hinged gate the brace usually runs from the bottom hinge corner up to the top latch corner, so it holds the gate in compression. Check this for your own design.
Is the span the length of the board?
No. It is the corner-to-corner distance. The cut length depends on the board width and the end cuts.
