Reference guide · Miter, crown molding and brace angles
Coving angle calculator: mitre and bevel for internal and external corners
By the Mirage Interactive team · Last checked
Coving meets itself at a corner on a compound angle, so a plain 45 degree cut is only right if you cut it in a mitre box with the coving held at its fitted angle. If you lay the coving flat on a compound mitre saw, you need two settings at once: a mitre (the turn of the saw) and a bevel (the tilt of the blade). Both depend on the wall angle and on the spring angle of the coving.
The spring angle is the angle between the back of the coving and the wall. A coving with equal wall and ceiling legs has a spring angle of 45 degrees. A coving that drops further down the wall than it projects across the ceiling has a smaller one, such as 38 degrees. This guide gives the settings for both, for the usual 90 degree corner and for walls that are out of square.
The short answer
For a 90 degree corner and a 45 degree spring angle, set the mitre to 35.3 degrees and the bevel to 30.0 degrees, with the coving laid flat on the saw table, back down.
For a 38 degree spring angle (a 52/38 profile) the same corner needs a mitre of 31.6 degrees and a bevel of 33.9 degrees. For any other size, find the spring angle from the two legs in the second table.
Tables
Settings in degrees for an internal corner, by the angle between the two walls. For an external corner, measure the angle your two walls make on the outside of the corner (normally 90 degrees) and use the same row. The second table starts from the leg sizes in millimetres and gives the spring angle and the settings for a 90 degree corner. Use your browser's print command to print this page: the tables print without the navigation.
| Wall angle (deg) | 45 deg spring: mitre | 45 deg spring: bevel | 38 deg spring: mitre | 38 deg spring: bevel |
|---|---|---|---|---|
| 80 | 40.1 | 32.8 | 36.3 | 37.1 |
| 85 | 37.7 | 31.4 | 33.9 | 35.5 |
| 90 | 35.3 | 30.0 | 31.6 | 33.9 |
| 95 | 32.9 | 28.5 | 29.4 | 32.2 |
| 100 | 30.7 | 27.0 | 27.3 | 30.4 |
| 105 | 28.5 | 25.5 | 25.3 | 28.7 |
| 110 | 26.3 | 23.9 | 23.3 | 26.9 |
| 120 | 22.2 | 20.7 | 19.6 | 23.2 |
| 135 | 16.3 | 15.7 | 14.3 | 17.6 |
Source: computed by the site build from the formulas below.
| Wall leg (mm) | Ceiling leg (mm) | Spring angle (deg) | Mitre (deg) | Bevel (deg) |
|---|---|---|---|---|
| 90 | 90 | 45.0 | 35.3 | 30.0 |
| 100 | 100 | 45.0 | 35.3 | 30.0 |
| 127 | 127 | 45.0 | 35.3 | 30.0 |
| 127 | 100 | 38.2 | 31.7 | 33.7 |
| 150 | 150 | 45.0 | 35.3 | 30.0 |
| 150 | 120 | 38.7 | 32.0 | 33.5 |
Source: computed by the site build from the formulas below.
Formulas
- Spring angle from the legs
- spring angle = arctan( ceiling leg / wall leg )
- The wall leg is how far the coving drops down the wall and the ceiling leg is how far it projects across the ceiling, both measured to the outer edges.
- Settings for coving laid flat
- mitre = arctan( sin(S) / tan(E / 2) ) bevel = arcsin( cos(S) x cos(E / 2) )
- S is the spring angle and E the angle between the two walls. The formula is for coving laid flat on the saw table, back down.
- Square corner, 45 degree spring
- mitre = arctan( sin 45 / tan 45 ) = 35.264 bevel = arcsin( cos 45 x cos 45 ) = 30
- This is the familiar 35.3 and 30 degree pair for 45/45 molding on a 90 degree corner.
Worked example
A 127 x 100 mm coving in a square internal corner
- The wall leg is 127 mm and the ceiling leg is 100 mm, so the spring angle is arctan(100 / 127) = 38.2 degrees.
- The corner is 90 degrees, so E / 2 = 45 degrees, tan 45 = 1 and cos 45 = 0.7071.
- Mitre = arctan( sin 38.2 / 1 ) = 31.7 degrees.
- Bevel = arcsin( cos 38.2 x 0.7071 ) = 33.7 degrees.
- For a coving with equal legs (45 degrees) the same corner gives 35.3 degrees of mitre and 30.0 degrees of bevel.
Things to watch
- Which way to turn the saw, and which side of the blade the piece goes on, depends on your saw, on which piece you are cutting and on whether it is an internal or an external corner. Check against your saw and cut a scrap first.
- The numbers assume a flat ceiling, plumb walls and a constant spring angle. Real rooms are rarely square: measure each corner and use the row that matches it.
- If your saw stops short of the mitre you need, or you prefer to cut in a mitre box or with a coping saw, these settings are not the ones to use. This page gives geometry only.
Related guide: Crown molding angle chart: miter and bevel settings for flat cuts
More from this family: Gate and diagonal brace angle calculator · Crown molding spring angle chart: miter and bevel by spring angle · Picture frame miter angle calculator: saw setting and cut length · Crown molding outside corner angles: miter and bevel settings
Skip the arithmetic
Miter Angle & Brace Calculator
Miter Angle & Brace Calculator gives compound miter and bevel settings for crown molding cut flat on the saw table, from the spring angle (52/38, 45/45 or your own), inside or outside corner and the wall angle. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
What angle do you cut coving at for a 90 degree corner?
Laid flat on a compound saw, a 45 degree spring coving takes a 35.3 degree mitre and a 30.0 degree bevel. A 38 degree spring takes 31.6 and 33.9 degrees.
How do I find the spring angle of my coving?
Measure how far it drops down the wall and how far it projects across the ceiling. The spring angle is the arctangent of the projection divided by the drop, measured from the wall.
Is the setting different for an external corner?
The numbers are the same for the same angle between the walls. What changes is which way the saw turns and which piece goes on which side.
