Reference guide · Pipe offsets, cut lengths and templates
Rolling offset calculator: true offset, travel and run for pipe
By the Mirage Interactive team · Last checked
A rolling offset moves a pipe up or down by the rise and sideways by the roll at the same time, so the two fittings sit in a tilted plane rather than a flat one. The trick is to turn the two movements into one: the true offset is the straight-line movement across the pipe, and from there it is an ordinary offset.
This page covers only that step, and the numbers that follow from it. For the basic flat offset and its multiplier chart, see the pipe offset formula guide linked below.
The short answer
True offset = square root of (rise squared + roll squared). Travel = true offset / sin(fitting angle), and run = true offset / tan(fitting angle). With 45 degree fittings the travel is 1.4142 times the true offset and the run equals it.
A 12 inch rise with a 9 inch roll is a 15 inch true offset (a 3-4-5 triangle). With 45 degree fittings the travel is 21.2132 inches and the run is 15.0 inches.
Tables
The first table gives the true offset for common rise and roll values in inches. The second works seven rise and roll pairs through 45 degree fittings, with the angle of the offset plane. The third gives the travel and run for a true offset at four fitting angles. Use your browser's print command to print this page: the tables print without the navigation.
| Rise (in) / roll (in) | 3 | 6 | 9 | 12 | 16 | 24 |
|---|---|---|---|---|---|---|
| 3 | 4.24 | 6.71 | 9.49 | 12.37 | 16.28 | 24.19 |
| 6 | 6.71 | 8.49 | 10.82 | 13.42 | 17.09 | 24.74 |
| 9 | 9.49 | 10.82 | 12.73 | 15.00 | 18.36 | 25.63 |
| 12 | 12.37 | 13.42 | 15.00 | 16.97 | 20.00 | 26.83 |
| 16 | 16.28 | 17.09 | 18.36 | 20.00 | 22.63 | 28.84 |
| 24 | 24.19 | 24.74 | 25.63 | 26.83 | 28.84 | 33.94 |
Source: computed by the site build from the formulas below.
| Rise (in) | Roll (in) | True offset (in) | Plane angle from the rise (deg) | Travel (in) | Run (in) |
|---|---|---|---|---|---|
| 6 | 6 | 8.49 | 45.00 | 12.000 | 8.485 |
| 8 | 6 | 10.00 | 36.87 | 14.142 | 10.000 |
| 9 | 12 | 15.00 | 53.13 | 21.213 | 15.000 |
| 12 | 9 | 15.00 | 36.87 | 21.213 | 15.000 |
| 10 | 10 | 14.14 | 45.00 | 20.000 | 14.142 |
| 12 | 16 | 20.00 | 53.13 | 28.284 | 20.000 |
| 24 | 18 | 30.00 | 36.87 | 42.426 | 30.000 |
Source: computed by the site build from the formulas below.
| True offset (in) | 22.5: travel | 22.5: run | 30: travel | 30: run | 45: travel | 45: run | 60: travel | 60: run |
|---|---|---|---|---|---|---|---|---|
| 4 | 10.45 | 9.66 | 8.00 | 6.93 | 5.66 | 4.00 | 4.62 | 2.31 |
| 6 | 15.68 | 14.49 | 12.00 | 10.39 | 8.49 | 6.00 | 6.93 | 3.46 |
| 8 | 20.91 | 19.31 | 16.00 | 13.86 | 11.31 | 8.00 | 9.24 | 4.62 |
| 10 | 26.13 | 24.14 | 20.00 | 17.32 | 14.14 | 10.00 | 11.55 | 5.77 |
| 15 | 39.20 | 36.21 | 30.00 | 25.98 | 21.21 | 15.00 | 17.32 | 8.66 |
| 20 | 52.26 | 48.28 | 40.00 | 34.64 | 28.28 | 20.00 | 23.09 | 11.55 |
| 25 | 65.33 | 60.36 | 50.00 | 43.30 | 35.36 | 25.00 | 28.87 | 14.43 |
Source: computed by the site build from the formulas below.
Formulas
- True offset
- true offset = sqrt( rise^2 + roll^2 )
- Rise is the movement in one direction across the pipe and roll is the movement at right angles to it. Both are measured centre to centre.
- Plane angle
- plane angle = arctan( roll / rise )
- The angle between the offset plane and the rise direction. A 12 by 9 offset sits at 36.87 degrees; swap the two numbers and it is 53.13.
- Travel and run
- travel = true offset / sin(angle) run = true offset / tan(angle)
- The travel is also the straight distance between the two fitting centres in space: sqrt( run^2 + rise^2 + roll^2 ).
Worked example
A 12 inch rise and a 9 inch roll with 45 degree fittings
- True offset = square root of ( 12 squared + 9 squared ) = square root of 225 = 15.0 inches.
- The offset plane is at arctan( 9 / 12 ) = 36.87 degrees from the rise direction.
- With 45 degree fittings the travel is 15.0 / sin 45 = 21.2132 inches, centre to centre.
- The run is 15.0 / tan 45 = 15.0 inches along the line of the pipe.
- Check in space: the square root of ( 15.0 squared + 12 squared + 9 squared ) is 21.2132, the same as the travel.
Things to watch
- Dimensions are centre to centre. Take the fitting take-outs off the travel to get the pipe you cut (see the pipe cut length and take-out chart).
- Check the fitting angle: fittings sold as 45 or 22.5 degrees are nominal angles, so measure a fitting you are unsure of.
- The model uses the outside surface of the pipe and ignores wall thickness. Dry-fit one piece before you cut the run.
Related guide: Pipe offset formula and multiplier chart
More from this family: Pipe miter template: cut-back chart and wrap ordinates · Pipe fitting take-out chart: cut length between fittings and parallel offsets · Pipe offset calculator: travel, run and fitting angle
Skip the arithmetic
Pipe Offset Layout Calculator
Pipe Offset Layout Calculator does rolling offsets from the rise and the roll, giving the true offset, travel and run, and works out the cut length from the travel and the take-outs. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do you calculate a rolling offset?
Find the true offset, the square root of the rise squared plus the roll squared, then treat it as an ordinary offset: travel is the true offset divided by the sine of the fitting angle.
What is the travel of a 12 by 9 rolling offset at 45 degrees?
21.2132 inches, centre to centre. The true offset is 15 inches.
Does swapping the rise and the roll change the pipe length?
No. The travel and run depend only on the true offset. Only the plane angle changes, from 36.87 to 53.13 degrees.
