Skip to content

Reference guide · Pipe offsets, cut lengths and templates

Pipe offset calculator: travel, run and fitting angle

By the Mirage Interactive team · Last checked

A simple offset moves a pipe sideways by a set distance using two matching fittings and a diagonal piece between them. The diagonal is the travel, and the length along the pipe that the offset takes up is the run. Two things are usually known: the offset, which comes from the drawing, and either the fitting angle or the space you have.

This guide goes both ways. From an offset and a fitting angle it gives the travel and the run. From an offset and the run that is available it gives the angle, so you can see which stock fitting is closest. Measurements are centre to centre; the cut length after the fitting take-outs is covered in the take-out guide linked below.

The short answer

Travel = offset / sin(angle). Run = offset / tan(angle). With the run known instead, angle = arctan(offset / run) and travel = the square root of (offset squared + run squared).

A 10 inch offset with 45 degree fittings has a travel of 14.142 inches and a run of 10.000 inches. A 10 inch offset in a 14 inch run needs a fitting angle of 35.54 degrees and a travel of 17.205 inches.

Tables

The first table gives the travel and the run, in inches, for eleven offsets at the four common fitting angles. The second gives the fitting angle for an offset and an available run, in degrees. Use your browser's print command to print this page: the tables print without the navigation.

Two matching fittings and a diagonal piece. The offset is the sideways distance, the travel is the diagonal between the fitting centres, and the run is the length along the pipe. Travel = offset / sin θ, run = offset / tan θ.
Travel and run (in) by offset (in) and fitting angle (degrees), centre to centre
Offset (in)22.5: travel22.5: run30: travel30: run45: travel45: run60: travel60: run
25.2264.8284.0003.4642.8282.0002.3091.155
410.4539.6578.0006.9285.6574.0004.6192.309
615.67914.48512.00010.3928.4856.0006.9283.464
820.90519.31416.00013.85611.3148.0009.2384.619
1026.13124.14220.00017.32114.14210.00011.5475.774
1231.35828.97124.00020.78516.97112.00013.8566.928
1539.19736.21330.00025.98121.21315.00017.3218.660
1847.03643.45636.00031.17725.45618.00020.78510.392
2462.71557.94148.00041.56933.94124.00027.71313.856
3078.39472.42660.00051.96242.42630.00034.64117.321
3694.07386.91272.00062.35450.91236.00041.56920.785

Source: computed by the site build from the formulas below.

Fitting angle (degrees) by offset (rows, in) and available run (columns, in)
Offset (in) / run (in)61012182436
645.031.026.618.414.09.5
1059.045.039.829.122.615.5
1263.450.245.033.726.618.4
1871.660.956.345.036.926.6
2476.067.463.453.145.033.7

Source: computed by the site build from the formulas below.

Formulas

Travel
travel = offset / sin(angle)
The distance between the two fitting centres. At 45 degrees it is 1.4142 times the offset, at 30 degrees 2 times, at 60 degrees 1.1547 times, at 22.5 degrees 2.6131 times.
Run
run = offset / tan(angle)
The length along the pipe the offset takes. At 45 degrees the run equals the offset.
Angle from the run
angle = arctan(offset / run)
Use it when the space is fixed. A result that is not a stock fitting angle means a different fitting, a shorter offset section or a cut elbow.
Travel from the run
travel = sqrt( offset^2 + run^2 )
The same diagonal, found from the two legs of the triangle.

Worked example

A 10 inch offset where the run is limited to 14 inches

  1. The angle that fits exactly is arctan(10 / 14) = 35.54 degrees, and the travel is sqrt(10^2 + 14^2) = 17.205 inches. That is not a stock angle.
  2. With 30 degree fittings the run is 10 / tan 30 degrees = 17.321 inches, which is longer than the 14 inches available, so they do not fit.
  3. With 45 degree fittings the run is 10.000 inches, which fits within the 14 inches. The travel is 10 / sin 45 degrees = 14.142 inches.
  4. The cut length is the travel less the take-out of each fitting. As an example only, with a take-out of 1.25 inches at each end: 14.142 - 2.5 = 11.642 inches. Take the real take-out from the fitting data for your pipe size and type.
  5. Check with the table: the 10 inch row at 45 degrees reads 14.142 for the travel and 10.000 for the run.

Things to watch

  • Offset and run are centre to centre, not edge to edge. If the drawing gives the outside edges, add or subtract the pipe diameter before using this page.
  • The travel is a centre to centre length. The cut length is shorter by the take-out of each fitting, and by any gap you leave for the joint.
  • Matching fittings on both ends give an offset. If the two angles differ, the pipe does not return to its original direction.
  • For an offset that moves in two directions at once, a rolling offset, see the rolling offset guide.

Related guide: Pipe offset formula and multiplier chart

More from this family: Pipe miter template: cut-back chart and wrap ordinates · Rolling offset calculator: true offset, travel and run for pipe · Pipe fitting take-out chart: cut length between fittings and parallel offsets

Skip the arithmetic

Pipe Offset Layout Calculator

Pipe Offset Layout Calculator does offset travel and run, rolling offset with rise and roll, parallel offsets and cut length from travel and take-outs, with a table of travel, run and shift factors, centre to centre. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

How do you calculate a pipe offset?

Divide the offset by the sine of the fitting angle for the travel, and by the tangent for the run. A 10 inch offset with 45 degree fittings has a travel of 14.142 inches.

What angle do I need when the run is limited?

Take the arctangent of the offset divided by the run. A 10 inch offset in a 14 inch run is 35.5 degrees.

What is the travel of a pipe offset?

The diagonal distance between the two fitting centres. It is 1.4142 times the offset at 45 degrees.