Reference guide · Pipe offsets, cut lengths and templates
Pipe miter template: cut-back chart and wrap ordinates
By the Mirage Interactive team · Last checked
A pipe miter wrap template is a paper strip that you wrap round the pipe. The curve on it marks a cut that is square to the pipe at one side and slanted at the other, so two cut pipes fit together as a bend. The strip is the pipe surface rolled flat, and the curve is a cosine wave.
A 90 degree elbow can be made from 2 to 5 pieces. More pieces mean smaller cut angles and a smoother bend. Each joint turns the pipe by twice its cut angle.
The short answer
Cut angle of each joint = turn / (2 x (pieces - 1)). For a 90 degree elbow that is 45 degrees for 2 pieces, 22.5 for 3, 15 for 4 and 11.25 for 5.
Cut-back from the throat to the heel of one cut = outside diameter x tan(cut angle). For a 2 piece 90 degree elbow the cut-back equals the outside diameter.
Tables
Cut-back from throat to heel in inches for a 90 degree elbow, by pipe outside diameter and number of pieces. The second table gives the wrap ordinates for NPS 6 as a 3-piece elbow. Use your browser's print command to print this page: the tables print without the navigation.
| Pipe | 2 pieces (45 deg) | 3 pieces (22.5 deg) | 4 pieces (15 deg) | 5 pieces (11.25 deg) |
|---|---|---|---|---|
| NPS 2 (2.375 in) | 2.38 | 0.98 | 0.64 | 0.47 |
| NPS 3 (3.5 in) | 3.50 | 1.45 | 0.94 | 0.70 |
| NPS 4 (4.5 in) | 4.50 | 1.86 | 1.21 | 0.90 |
| NPS 6 (6.625 in) | 6.63 | 2.74 | 1.78 | 1.32 |
| NPS 8 (8.625 in) | 8.63 | 3.57 | 2.31 | 1.72 |
| NPS 10 (10.75 in) | 10.75 | 4.45 | 2.88 | 2.14 |
| NPS 12 (12.75 in) | 12.75 | 5.28 | 3.42 | 2.54 |
Source: computed by the site build from the formulas below.
| Station | Angle round pipe (deg) | Distance along strip (in) | Cut-back from throat line (in) |
|---|---|---|---|
| 0 | 0.0 | 0.00 | 0.000 |
| 1 | 22.5 | 1.30 | 0.104 |
| 2 | 45.0 | 2.60 | 0.402 |
| 3 | 67.5 | 3.90 | 0.847 |
| 4 | 90.0 | 5.20 | 1.372 |
| 5 | 112.5 | 6.50 | 1.897 |
| 6 | 135.0 | 7.80 | 2.342 |
| 7 | 157.5 | 9.11 | 2.640 |
| 8 | 180.0 | 10.41 | 2.744 |
Source: computed by the site build from the formulas below.
Formulas
- Cut angle of each joint
- cut angle = turn / (2 x (pieces - 1))
- The end pieces are cut once and the middle pieces are cut at both ends.
- Cut-back
- cut-back = OD x tan(cut angle)
- OD is the outside diameter of the pipe. The model is the outside surface of the pipe and wall thickness is ignored.
- Ordinate at station k of n
- y(k) = (OD / 2) x tan(cut angle) x (1 - cos(360 x k / n)) distance along the strip = pi x OD x k / n
- With n = 16 the stations are 22.5 degrees apart. The second half of the strip repeats the first half in reverse.
Worked example
An NPS 6 pipe as a 3-piece 90 degree elbow
- Each joint turns the pipe 45 degrees, so the cut angle is 90 / (2 x 2) = 22.5 degrees.
- The cut-back is 6.625 x tan 22.5 = 2.74 inches from throat to heel.
- The strip is pi x 6.625 = 20.81 inches long. Station spacing is 1.30 inches.
- The ordinate at station 4 (a quarter of the way round) is 1.372 inches, and at station 8 (the heel) it is 2.744 inches.
Things to watch
- Print a template at 100 percent, with no "fit to page" scaling, and check it against a ruler before you use it. A printout that is a few percent small makes a bad fit.
- Wrap the strip so that its edges meet exactly, and cut a scrap piece first. This page gives numbers and shapes only. It does not say a joint meets any code, and does not cover welds or supports.
- Mark the throat line first, then the 16 stations.
Related guide: Pipe offset formula and multiplier chart
More from this family: Rolling offset calculator: true offset, travel and run for pipe · Pipe fitting take-out chart: cut length between fittings and parallel offsets · Pipe offset calculator: travel, run and fitting angle
Skip the arithmetic
Pipe Offset Layout Calculator
Pipe Offset Layout Calculator prints miter wrap templates for 2 to 5 pieces at true scale, and lateral, branch and off-centre branch wrap templates too. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How many pieces should a 90 degree elbow have?
Two pieces are quick but give a sharp bend. Three to five pieces flow better. The more pieces, the smaller the cut angle and the more cuts you make.
Are lateral and branch templates different?
Yes. A lateral or a branch wraps round the header as well, so the curve is not a simple cosine. The app lists those templates separately.
Why check a printed template against a ruler?
Printers can scale a page without telling you. A template is only right at true size.
