Skip to content

Reference guide · Pipe offsets, cut lengths and templates

Pipe fitting take-out chart: cut length between fittings and parallel offsets

By the Mirage Interactive team · Last checked

The travel of an offset is measured from the centre of one fitting to the centre of the other. The pipe you cut is shorter, because each fitting takes up some of that distance. That allowance is the take-out: from the corner where the two straight centrelines meet to the point where the fitting ends.

For a circular-arc elbow the take-out follows from the radius and the turn. This guide gives it for long-radius elbows by pipe size, the cut length of a 45 degree offset, and how far parallel pipes have to be set back from each other so they stay evenly spaced round the turn.

The short answer

Take-out = radius x tan(turn / 2). For a long-radius elbow the radius is 1.5 times the nominal pipe size, so a 90 degree elbow takes out exactly that radius and a 45 degree elbow takes out 0.4142 of it.

Cut length = travel - take-out at one end - take-out at the other. For a 10 inch offset with NPS 4 long-radius 45 degree elbows the travel is 14.1421 inches, each take-out is 2.4853 inches and the cut is 9.1716 inches.

Tables

The first table gives the take-out of long-radius elbows by nominal pipe size and angle. The second gives the cut length for 45 degree offsets in NPS 4 pipe. The third gives the setback between parallel pipes by centre spacing and fitting angle. Use your browser's print command to print this page: the tables print without the navigation.

Take-out (in) of a long-radius elbow, radius 1.5 x nominal size, by angle
PipeRadius (in)90 deg60 deg45 deg22.5 deg
NPS 23.003.00001.73211.24260.5967
NPS 34.504.50002.59811.86400.8951
NPS 46.006.00003.46412.48531.1935
NPS 69.009.00005.19623.72791.7902
NPS 812.0012.00006.92824.97062.3869
NPS 1015.0015.00008.66036.21322.9837
NPS 1218.0018.000010.39237.45583.5804

Source: computed by the site build from the formulas below.

Cut length (in) of the diagonal for a 45 degree offset in NPS 4 pipe with long-radius 45 degree elbows
Offset (in)Travel (in)Take-out each end (in)Cut length (in)
68.48532.48533.5147
811.31372.48536.3431
1014.14212.48539.1716
1216.97062.485312.0000
1825.45582.485320.4853
2433.94112.485328.9706

Source: computed by the site build from the formulas below.

Setback (in) of each next parallel pipe, by centre spacing and fitting angle
Spacing (in)22.5 deg30 deg45 deg60 deg
40.79561.07181.65692.3094
61.19351.60772.48533.4641
81.59132.14363.31374.6188
101.98912.67954.14215.7735
122.38693.21544.97066.9282

Source: computed by the site build from the formulas below.

Formulas

Take-out of an elbow
take-out = R x tan( turn / 2 )
R is the centreline radius of the elbow, and the turn is its deflection: 45 degrees for a 45 degree elbow. For a long-radius elbow R = 1.5 x nominal pipe size.
Cut length
cut = travel - take-out 1 - take-out 2
Travel is the centre-to-centre distance of the offset. Leave a gap for the joint if your method needs one, and take it off as well.
Parallel offsets
setback = spacing x tan( angle / 2 )
Pipes that run side by side and turn together: each pipe further out on the turn starts its bend this much later along the run than the one inside it.

Worked example

A 10 inch offset in NPS 4 pipe with long-radius 45 degree elbows

  1. The long-radius radius is 1.5 x 4 = 6.0 inches. Each 45 degree take-out is 6.0 x tan 22.5 = 2.4853 inches.
  2. The travel is 10 / sin 45 = 14.1421 inches, centre to centre.
  3. The cut length is 14.1421 - 2 x 2.4853 = 9.1716 inches.
  4. A second pipe 6 inches away, running parallel and turning with the first, starts its bend 6 x tan 22.5 = 2.4853 inches later at 45 degrees. At 30 degrees the setback is 1.6077 inches.
  5. Catalogue dimensions are rounded: the tabulated centre-to-end of an NPS 4 long-radius 45 degree elbow is 64 mm (2.5197 inches), against 63.1 mm from the formula. With 64 mm the cut would be 9.1028 inches, 0.07 inch shorter. Use the dimension of the fitting you are actually fitting.

Things to watch

  • The formula treats the elbow as a circular arc. Only 45 and 90 degree long-radius elbows have standard tabulated dimensions, so the 60 and 22.5 degree columns are computed values, not catalogue ones. Measure your fittings.
  • Short-radius elbows, reducing fittings and weld gaps have different take-outs. This page covers long-radius elbows only.
  • The page gives numbers and does not say a layout meets any code or standard. Dry-fit before you cut.

Related guide: Pipe offset formula and multiplier chart

More from this family: Pipe miter template: cut-back chart and wrap ordinates · Rolling offset calculator: true offset, travel and run for pipe · Pipe offset calculator: travel, run and fitting angle

Skip the arithmetic

Pipe Offset Layout Calculator

Pipe Offset Layout Calculator works out the cut length from the travel and the take-outs, does parallel offsets for a set of pipes, and lists the travel, run and shift factors in a multiplier table with an optional gap at each end. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

What is the take-out of a 45 degree long-radius elbow?

0.4142 times the radius, so 0.6213 times the nominal pipe size. For NPS 4 that is 2.4853 inches from the formula; the catalogue value is rounded to 64 mm.

How do I get the cut length of an offset?

Take the travel, which is the offset divided by the sine of the fitting angle, and subtract the take-out of each fitting.

Why do parallel pipes need different lengths?

Each pipe further out on the turn has a longer diagonal and starts its bend later. The setback between neighbouring pipes is the spacing times tan(angle / 2).