Reference guide · Stair rise, run and stringer marks
Stair stringer length calculator: board length, pitch line and throat
By the Mirage Interactive team · Last checked
A stringer length is asked three ways: how long is the cut line along the notches, how long is the straight line from the foot to the top, and what board do I buy. They are three different numbers, and only the last is the one to take to the lumber yard.
This guide gives all three, with the notch depth and the wood left under the notches, called the throat, for a 2x12 stringer.
The short answer
Diagonal = square root of (total rise squared + total run squared). Pitch line = (risers - 1) x square root of (unit rise squared + unit run squared). The shortest straight board is the extent of the whole notched outline along the cut line, and the app reports it when you give a board depth.
For a 95 1/16 inch rise with 13 risers and a 10 3/16 inch run, the diagonal is 154.86 inches, the pitch line 150.48 inches and the shortest board 154.16 inches (154 3/16).
Tables
Stringer lengths for common total rises, aiming at a 7 1/4 inch riser, with a 10 inch tread run, 1 inch thick treads and a 2x12 stringer of 11 1/4 inches actual depth. All lengths are in inches, with the nearest 1/16 inch in brackets. Use your browser's print command to print this page: the tables print without the navigation.
| Total rise (in) | Risers | Unit rise (in) | Total run (in) | Diagonal | Pitch line | Shortest board | Throat (in) |
|---|---|---|---|---|---|---|---|
| 60 | 8 | 7.500 | 70.0 | 92.20 (92 3/16) | 87.50 (87 1/2) | 91.40 (91 3/8) | 5.25 |
| 72 | 10 | 7.200 | 90.0 | 115.26 (115 1/4) | 110.90 (110 7/8) | 114.52 (114 1/2) | 5.41 |
| 84 | 12 | 7.000 | 110.0 | 138.41 (138 3/8) | 134.27 (134 1/4) | 137.71 (137 11/16) | 5.52 |
| 96 | 13 | 7.385 | 120.0 | 153.67 (153 11/16) | 149.17 (149 3/16) | 152.97 (152 15/16) | 5.31 |
| 108 | 15 | 7.200 | 140.0 | 176.82 (176 13/16) | 172.51 (172 1/2) | 176.14 (176 1/8) | 5.41 |
| 120 | 17 | 7.059 | 160.0 | 200.00 (200) | 195.85 (195 7/8) | 199.34 (199 5/16) | 5.48 |
Source: computed by the site build from the formulas below.
Formulas
- Diagonal
- diagonal = square root of (total rise^2 + total run^2) total run = treads x unit run
- The rise-and-run hypotenuse. Printed layouts often call it the stringer length. It is not a cut length: the board follows the cut line.
- Pitch line and notch depth
- step length = square root of (unit rise^2 + unit run^2) pitch line = (risers - 1) x step length notch depth = unit rise x unit run / step length
- The pitch line runs through the tips of the notches. The notch depth is measured square to it, from the inside corner to the cut line.
- Throat
- throat = board depth - notch depth
- The wood left square to the cut line under the inside corners of the notches. The app reports it as a number and sets no minimum; your local code or an engineer decides how much is enough.
- Shortest straight board
- extent of the notched outline, measured along the cut line
- The outline has the foot at the lower floor, a level cut at the bottom, a plumb cut at the top and the notches between. The shortest straight board that holds it is the extent of those corners along the cut line. Round up to the next length your supplier cuts.
Worked example
A 95 1/16 inch rise, 13 risers, 10 3/16 inch run, 1 inch treads, 2x12
- Unit rise = 95.0625 / 13 = 7.3125 inches (7 5/16). Unit run is 10.1875 inches (10 3/16). There are 12 treads, so the total run is 12 x 10.1875 = 122.25 inches.
- Diagonal = square root of (95.0625^2 + 122.25^2) = 154.861 inches (154 7/8). Step length = square root of (7.3125^2 + 10.1875^2) = 12.540 inches, so the pitch line is 12 x 12.540 = 150.483 inches.
- Notch depth = 7.3125 x 10.1875 / 12.540 = 5.9406 inches. A 2x12 is 11 1/4 inches deep, so the throat is 11.25 - 5.9406 = 5.3094 inches.
- The shortest straight board that holds the outline is 154.164 inches (154 3/16), which is 12 ft 10 3/16 inches. Lumber is usually sold in 2 ft steps, so the next length up is 14 ft.
- Check on the diagonal alone: a 95 inch rise and a 122 inch run give square root of (9025 + 14884) = 154.63 inches, the 154 5/8 inches that a printed layout shows. It is a check on the rise and run, not a board length.
Things to watch
- Use the diagonal to check the rise and run and to estimate. Buy and cut from the shortest board length, plus whatever you want to trim.
- The throat is reported only as a number here and in the app. Building codes and stringer makers set limits for it, and your inspector decides.
- The tables take the first riser as 1 inch shorter because of the 1 inch tread thickness, as the app does. With a different tread thickness the lengths change by a fraction of an inch.
Related guide: Stair stringer layout: rise, run and code limits
More from this family: Stair stringer calculator with a landing · Stair rise and run calculator: unit rise, unit run and total run
Skip the arithmetic
Stair Calculator: Stringers
Stair Calculator: Stringers shows the stringer in a diagram with its cut line, pitch line length and notch depth, and gives the cut angles for the framing square and a cut list for every riser. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How long is a stair stringer?
For a 95 1/16 inch rise and 12 treads of 10 3/16 inches, the cut line is 150.5 inches and the shortest straight board is 154 3/16 inches, so a 14 ft board.
What is the throat of a stair stringer?
The wood left under the inside corner of a notch, measured square to the cut line: board depth minus notch depth. It is 5.31 inches in the example.
Is the rise-and-run diagonal the length of the stringer?
No. It is the straight line from the foot to the point above the top end. The board follows the cut line and needs its own length, as the table shows.
