Skip to content

Reference guide · Stair rise, run and stringer marks

Stair stringer layout: rise, run and code limits

By the Mirage Interactive team · Last checked

Stair stringer layout starts with one number, the total rise from finished floor to finished floor, and ends with a stringer you can mark with a framing square. In between you choose how many risers there are, which fixes the height of every step, and a tread run, which fixes the slope.

Every riser in a flight must be the same height, so the layout divides the total rise equally rather than picking a riser height and living with the leftover.

Printable table

Riser count and unit rise for common total rises, aiming at a 7.25 in riser and a 10 in tread. Use your browser's print command to print this page: the tables print without the navigation.

Riser count and unit rise for common total rises (aiming at a 7.25 in riser and a 10 in tread, top at the upper floor)
Total rise (in)RisersUnit rise (in)TreadsTotal run (in)Slope angle (deg)Rise + run (in)2 x rise + run (in)
3047.500330.0036.917.5025.00
3657.200440.0035.817.2024.40
4267.000550.0035.017.0024.00
4876.857660.0034.416.8623.71
5477.714660.0037.617.7125.43
6087.500770.0036.917.5025.00
72107.200990.0035.817.2024.40
84127.00011110.0035.017.0024.00
96137.38512120.0036.417.3824.77
108157.20014140.0035.817.2024.40
120177.05916160.0035.217.0624.12

Source: The Stair app's reference calculator (stair), the one behind the app's stair and step test cases.

Formulas

Riser count and unit rise
risers N = round( total rise / target riser height ) unit rise R = total rise / N
Round to the nearest whole number, then recompute the riser height so all risers are equal.
Treads and total run
treads = N - 1 (top step is the upper floor) total run = treads x tread run
If the stair ends on its own top tread, treads = N.
Comfort rules of thumb
R + run = 17 to 18 in 2R + run = 24 to 25 in
Rules of thumb for a comfortable stair. They are not code limits.
Slope and stringer
angle = arctan(R / run) pitch line = treads x square root of (R squared + run squared)
The pitch line runs along the nosings. Plumb cut = angle from the square; level cut = 90 degrees - angle.

Worked example

A 105 inch total rise

  1. Target riser 7.25 in: 105 / 7.25 = 14.48, so use 14 risers.
  2. Unit rise = 105 / 14 = 7.500 in. With the top step on the upper floor there are 13 treads.
  3. At a 10 in tread the total run is 13 x 10 = 130 in.
  4. R + run = 17.50 in and 2R + run = 25.00 in, inside both comfort ranges.
  5. Slope = arctan(7.5 / 10) = 36.87 degrees: plumb cut 36.87 degrees and level cut 53.13 degrees from the square.
  6. Pitch line length = 13 x 12.5 in = 162.5 in (4127.5 mm).

Things to watch

  • Typical limits in a US residential code (the IRC, section R311.7): riser at most 7 3/4 in, tread at least 10 in, no more than 3/8 in difference between the largest and smallest riser or tread in a flight, at most 12 ft 7 in of rise between landings, and at least 6 ft 8 in of headroom. Codes differ by place and building type, and your inspector decides.
  • Allow for the thickness of the finished tread: the usual practice is to trim one tread thickness off the bottom of the stringer so the first step is the same height as the rest.
  • The calculator linked below does geometry only. It does not check these limits.

Related guide: Stair stringer calculator with a landing · Stair rise and run calculator: unit rise, unit run and total run · Stair stringer length calculator: board length, pitch line and throat

Skip the arithmetic

Stair Calculator: Stringers

Riser count, unit rise and run, stringer cut marks and 1:1 step templates from the rise you measured. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.

Questions

How many risers do I need?

Divide the total rise by the riser height you want and round to the nearest whole number. Then divide the total rise by that number to get the exact, equal riser height.

How many treads are there?

One fewer than the risers when the top step is the upper floor, and the same number as the risers when the stair ends on its own top tread.