Reference guide · Rafter lengths, cuts and birdsmouth
Shed roof rafter length calculator: rise, run and rafter length
By the Mirage Interactive team · Last checked
A shed roof, also called a lean-to or mono-pitch roof, is one slope from a low wall to a high one. There is no ridge, so every rafter is the sloping side of a right triangle: the run is the horizontal distance between the bearing lines, the rise is how much higher the high wall stands, and the rafter follows the hypotenuse.
Two numbers matter most when you frame one: how much taller the high wall must be, and how long to cut each rafter. Both follow from the width of the building, the pitch and the width of the high wall plate.
The short answer
Run = building width (outside to outside) - width of the high wall plate. Rise = run x pitch / 12. Rafter line length = run x k, where k = square root of (1 + (pitch / 12) squared).
Overall length with overhangs = (low overhang + run + plate width + high overhang) x k. With the same birdsmouth at both walls, the top of the high plate stands higher than the low one by exactly the rise.
Tables
The first table gives how much higher the top of the high wall plate stands than the low one (the rise) by building width and pitch, for a 3 1/2 inch high wall plate and the same birdsmouth at both walls. The second gives the overall rafter length with a 12 inch overhang at each end, for the same widths. All in inches. Use your browser's print command to print this page: the tables print without the navigation.
| Building width (ft) | 2/12 | 3/12 | 4/12 | 5/12 | 6/12 |
|---|---|---|---|---|---|
| 8 | 15.42 (15 7/16) | 23.13 (23 1/8) | 30.83 (30 13/16) | 38.54 (38 9/16) | 46.25 (46 1/4) |
| 10 | 19.42 (19 7/16) | 29.13 (29 1/8) | 38.83 (38 13/16) | 48.54 (48 9/16) | 58.25 (58 1/4) |
| 12 | 23.42 (23 7/16) | 35.13 (35 1/8) | 46.83 (46 13/16) | 58.54 (58 9/16) | 70.25 (70 1/4) |
| 14 | 27.42 (27 7/16) | 41.13 (41 1/8) | 54.83 (54 13/16) | 68.54 (68 9/16) | 82.25 (82 1/4) |
| 16 | 31.42 (31 7/16) | 47.13 (47 1/8) | 62.83 (62 13/16) | 78.54 (78 9/16) | 94.25 (94 1/4) |
Source: computed by the site build from the formulas below.
| Building width (ft) | 3/12 | 4/12 | 6/12 |
|---|---|---|---|
| 8 | 123.69 (123 11/16) | 126.49 (126 1/2) | 134.16 (134 3/16) |
| 10 | 148.43 (148 7/16) | 151.79 (151 13/16) | 161.00 (161) |
| 12 | 173.17 (173 3/16) | 177.09 (177 1/16) | 187.83 (187 13/16) |
| 14 | 197.91 (197 15/16) | 202.39 (202 3/8) | 214.66 (214 11/16) |
| 16 | 222.65 (222 5/8) | 227.68 (227 11/16) | 241.50 (241 1/2) |
Source: computed by the site build from the formulas below.
Formulas
- Run and rise
- run = width - plate rise = run x pitch / 12
- Width is from the outer face of the low wall to the outer face of the high wall plate. The high end of the rafter bears on the inner face of the high plate, so the plate width is not part of the run. For a rafter on a ledger fixed to a wall, the run is the width less the ledger thickness.
- Length along the slope
- line length = run x k k = square root of (1 + (pitch / 12)^2)
- Top edge of the rafter, from the plumb line at the outer face of the low wall to the plumb line at the inner face of the high plate.
- Overall length
- overall = (low overhang + run + plate + high overhang) x k
- The overhangs are horizontal, measured from the outer face of each wall.
- Heel cut and height difference
- heel = seat x pitch / 12 high plate top - low plate top = rise + high heel - low heel
- With equal seats the two heels cancel and the height difference is the rise.
Worked example
A shed 10 ft wide at 4/12 with 2x6 rafters
- Width 120 inches, plate and seat 3 1/2 inches, so the run is 120 - 3.5 = 116.5 inches. Pitch 4/12 gives k = 1.0541, which is 12.65 inches of rafter per foot of run.
- Rise = 116.5 x 4 / 12 = 38.833 inches (38 13/16): the top of the high plate stands that much above the low one when both birdsmouths are the same.
- Line length = 116.5 x 1.0541 = 122.80 inches (122 13/16).
- With a 12 inch overhang at the low wall and 6 inches at the high wall, overall = (12 + 116.5 + 3.5 + 6) x 1.0541 = 138 x 1.0541 = 145.46 inches (145 7/16).
- A 3 1/2 inch seat on 4/12 gives a heel cut of 3.5 x 4 / 12 = 1.167 inches (1 3/16) at each wall. A 2x6 is 5 1/2 inches deep, so its plumb depth is 5.5 x 1.0541 = 5.80 inches and 4.63 inches of rafter stands above the plate at the heel.
- Marks along the top edge from the tail end: 0.00, 12.65, 16.34, 135.45, 139.14, 145.46 inches (tail end, low heel line, end of the low seat, high heel line, end of the high seat, end cut). The plumb cut is 18.43 degrees from square and the level cut 71.57 degrees from square.
Things to watch
- This guide covers a rafter bearing on a high wall plate. Where the high end bears on a ledger board on an existing wall, the run is the width less the ledger thickness and the rafter has a plumb cut against the wall.
- Check the pitch against the roofing you plan to use. Roofing makers set a minimum pitch for each product, and they differ.
- This is geometry only. It does not check spans, rafter sizes, loads, uplift or code. Cut the first rafter, try it in place and use it as the pattern.
Related guide: Rafter length and pitch table
More from this family: Hip rafter calculator: length formula and cuts · Birdsmouth cut depth calculator: seat, heel and share of the rafter · Rafter length calculator with overhang and ridge board
Skip the arithmetic
Roof Framing Calculator & Cuts
Roof Framing Calculator & Cuts gives the length along the top edge, plumb, level and seat cuts, birdsmouth and tail of a common rafter from the pitch and run: for a shed roof, type the run and leave the ridge board at zero. One-time purchase · No subscription · Price shown in your store. Works offline, no ads, no account.
Questions
How do I calculate rafter length for a shed roof?
Take the building width less the width of the high wall plate for the run, multiply it by the length factor for the pitch, and add each overhang multiplied by the same factor.
How much higher is the high wall of a shed roof?
The run times the pitch divided by 12. A 10 ft wide shed at 4/12 stands about 38 13/16 inches higher with a 3 1/2 inch high plate.
Can I use a common rafter calculator for a shed roof?
Yes. Type the shed's run, which is the width less the high plate, and ignore the ridge. The length along the top edge is the same as a common rafter of that run with no ridge board.
